Related Experiment Video

Updated: Jun 22, 2026

Microfluidic Fabrication of Polymeric and Biohybrid Fibers with Predesigned Size and Shape
07:38

Microfluidic Fabrication of Polymeric and Biohybrid Fibers with Predesigned Size and Shape

Published on: January 8, 2014

Bend-resistant design of conventional and microstructure fibers with very large mode area

John M Fini

    Optics Express
    |June 9, 2009
    PubMed

    More Related Videos

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

    Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

    Published on: May 23, 2017

    Prescribed 3-D Direct Writing of Suspended Micron/Sub-micron Scale Fiber Structures via a Robotic Dispensing System10:36

    Prescribed 3-D Direct Writing of Suspended Micron/Sub-micron Scale Fiber Structures via a Robotic Dispensing System

    Published on: June 12, 2015

    Related Concept Videos

    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    Members Made of Elastoplastic Material01:19

    Members Made of Elastoplastic Material

    The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
    As the bending moment...
    Design of Prismatic Beams for Bending01:23

    Design of Prismatic Beams for Bending

    The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and stress...
    Plastic Deformations01:14

    Plastic Deformations

    It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
    Plastic Deformations01:19

    Plastic Deformations

    Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their original...
    Fiber Reinforced Concrete01:22

    Fiber Reinforced Concrete

    Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...