Related Experiment Video

Updated: Jun 22, 2026

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System
12:08

Fabrication of High Contrast Gratings for the Spectrum Splitting Dispersive Element in a Concentrated Photovoltaic System

Published on: July 18, 2015

Design of SiON-based grating-assisted vertical directional couplers

Vittorio Passaro, Goran Masanovic

    Optics Express
    |June 9, 2009
    PubMed

    More Related Videos

    Fabrication and Characterization of Superconducting Resonators10:26

    Fabrication and Characterization of Superconducting Resonators

    Published on: May 21, 2016

    Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities11:08

    Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

    Published on: November 30, 2012

    Related Concept Videos

    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...
    Design of Prismatic Beams for Bending01:23

    Design of Prismatic Beams for Bending

    The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and stress...
    Design Example: Design of an Irrigation Channel01:27

    Design Example: Design of an Irrigation Channel

    Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
    Directional Relays01:25

    Directional Relays

    Directional relays, essential for managing unidirectional fault currents, enhance the safety and efficiency of power systems. On power lines equipped with directional relays, faults downstream (to the right) of the current transformer typically cause the fault current to lag the bus voltage by approximately 90 degrees, known as the forward direction. In contrast, upstream (left-side) faults may result in the fault current leading the bus voltage by nearly 90 degrees, termed the reverse...
    Design of Columns under a Centric Load01:17

    Design of Columns under a Centric Load

    The design of columns under centric load is a fundamental aspect of structural engineering and is critical for ensuring the stability and integrity of structures. Euler's and Secant's formulas are central to understanding and calculating the critical load and deformation behaviors of columns, providing a basis for safe and effective structural design.
    Euler's formula is applicable under the assumption that the column is a perfect, straight, homogenous prism, and it is operating within the...