Related Experiment Video

Updated: Jun 20, 2026

Thermochemical Studies of Ni(II) and Zn(II) Ternary Complexes Using Ion Mobility-Mass Spectrometry
16:11

Thermochemical Studies of Ni(II) and Zn(II) Ternary Complexes Using Ion Mobility-Mass Spectrometry

Published on: June 8, 2022

Full-configuration-interaction calculation of three-body nonadditive contribution to helium interaction potential

Wojciech Cencek1, Konrad Patkowski, Krzysztof Szalewicz

  • 1Department of Physics and Astronomy, University of Delaware, Newark, Delaware 19716, USA. cencek@physics.udel.edu

The Journal of Chemical Physics
|August 21, 2009
PubMed

More Related Videos

Isotopic Effect in Double Proton Transfer Process of Porphycene Investigated by Enhanced QM/MM Method05:51

Isotopic Effect in Double Proton Transfer Process of Porphycene Investigated by Enhanced QM/MM Method

Published on: July 19, 2019

Computation of Atmospheric Concentrations of Molecular Clusters from ab initio Thermochemistry12:11

Computation of Atmospheric Concentrations of Molecular Clusters from ab initio Thermochemistry

Published on: April 8, 2020

Related Concept Videos

Hess's Law03:40

Hess's Law

There are two ways to determine the amount of heat involved in a chemical change: measure it experimentally, or calculate it from other experimentally determined enthalpy changes. Some reactions are difficult, if not impossible, to investigate and make accurate measurements for experimentally. And even when a reaction is not hard to perform or measure, it is convenient to be able to determine the heat involved in a reaction without having to perform an experiment.
Nuclear Binding Energy02:13

Nuclear Binding Energy

The difference between the calculated and experimentally measured masses is known as the mass defect of the atom. In the case of helium-4, the mass defect indicates a “loss” in mass of 4.0331 amu – 4.0026 amu = 0.0305 amu. The loss in mass accompanying the formation of an atom from protons, neutrons, and electrons is due to the conversion of that mass into energy that is evolved as the atom forms. The nuclear binding energy is the energy produced when the atoms’ nucleons are bound together;...
Real Gases: Effects of Intermolecular Forces and Molecular Volume Deriving Van der Waals Equation04:01

Real Gases: Effects of Intermolecular Forces and Molecular Volume Deriving Van der Waals Equation

Thus far, the ideal gas law, PV = nRT, has been applied to a variety of different types of problems, ranging from reaction stoichiometry and empirical and molecular formula problems to determining the density and molar mass of a gas. However, the behavior of a gas is often non-ideal, meaning that the observed relationships between its pressure, volume, and temperature are not accurately described by the gas laws.
Force and Potential Energy in Three Dimensions01:04

Force and Potential Energy in Three Dimensions

Consider a particle moving under the action of a conservative force that has components along each coordinate axis. Each component of force is a function of the coordinates. The potential energy function U is also a function of all three spatial coordinates. Force in one dimension can be written as the negative ratio of potential energy change to the displacement along that coordinate. For minimal displacement, the ratios become derivatives. If a function has many variables, the derivative only...
Van der Waals Equation01:10

Van der Waals Equation

The ideal gas law is an approximation that works well at high temperatures and low pressures. The van der Waals equation of state (named after the Dutch physicist Johannes van der Waals, 1837−1923) improves it by considering two factors.
First, the attractive forces between molecules, which are stronger at higher densities and reduce the pressure, are considered by adding to the pressure a term equal to the square of the molar density multiplied by a positive coefficient a. Second, the volume...
Equations of Equilibrium in Three Dimensions01:30

Equations of Equilibrium in Three Dimensions

When analyzing structures or systems at rest, it is necessary to ensure they are in equilibrium. This is where the vector and scalar equations of equilibrium come into play. These equations are crucial in ensuring a structure is stable and will not collapse or fall apart. The vector and scalar equations of equilibrium provide a framework for analyzing the forces acting on a body.
According to the vector equations of equilibrium, the vector sum of all the external forces acting on a body must...