Related Experiment Video

Updated: Jun 20, 2026

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator
08:39

Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

Published on: January 28, 2019

Design of optimal binary phase and amplitude filters for maximization of correlation peak sharpness

J D Downie

    Optics Letters
    |September 24, 2009
    PubMed

    More Related Videos

    Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques09:01

    Gain-compensation Methodology for a Sinusoidal Scan of a Galvanometer Mirror in Proportional-Integral-Differential Control Using Pre-emphasis Techniques

    Published on: April 4, 2017

    Related Concept Videos

    Design Example01:23

    Design Example

    The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any finite,...
    Active Filters01:25

    Active Filters

    Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations01:08

    IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations

    Identical bonds within a polyatomic group can stretch symmetrically (in-phase) or asymmetrically (out-of-phase). Similar to hydrogen bonding, these vibrations also influence the shape of the IR peak. Generally, asymmetric stretching frequencies are higher than symmetric stretching frequencies. For example, primary amines exhibit two distinct IR peaks between 3300–3500 cm−1 corresponding to the symmetric and asymmetric N-H stretching, while secondary amines exhibit a single stretching vibration...
    Linear Approximation in Frequency Domain01:26

    Linear Approximation in Frequency Domain

    Linear systems are characterized by two main properties: superposition and homogeneity. Superposition allows the response to multiple inputs to be the sum of the responses to each individual input. Homogeneity ensures that scaling an input by a scalar results in the response being scaled by the same scalar.
    In contrast, nonlinear systems do not inherently possess these properties. However, for small deviations around an operating point, a nonlinear system can often be approximated as linear.