Related Experiment Video

Updated: Jun 20, 2026

Installation Method to Enhance Quality Control for Fiber Reinforced Polymer Spike Anchors
06:21

Installation Method to Enhance Quality Control for Fiber Reinforced Polymer Spike Anchors

Published on: April 10, 2018

Falls from height during the floor slab formwork of buildings: current situation in Spain

Jose M Adam1, Francisco J Pallarés, Pedro A Calderón

  • 1ICITECH, Departamento de Ingeniería de la Construcción y Proyectos de Ingeniería Civil, Universidad Politécnica de Valencia, Camino de Vera s/n, 46071 Valencia, Spain. joadmar@cst.upv.es

Journal of Safety Research
|September 26, 2009
PubMed
Abstract

More Related Videos

Design and Analysis for Fall Detection System Simplification08:05

Design and Analysis for Fall Detection System Simplification

Published on: April 6, 2020

Laboratory and Field Protocol for Estimating Sheet Erosion Rates from Dendrogeomorphology07:20

Laboratory and Field Protocol for Estimating Sheet Erosion Rates from Dendrogeomorphology

Published on: January 7, 2019

Related Concept Videos

Shrinkage in Concrete01:27

Shrinkage in Concrete

Shrinkage in concrete is primarily due to water loss from evaporation, hydration of cement, or carbonation, leading to a reduction in volume. The volumetric contraction results in volumetric strain in concrete. However, in practice, shrinkage is measured as linear strain, which is one-third of the volumetric strain.
When concrete is still in its plastic state, it can undergo a decrease in volume by about 1% of its absolute volume. This decrease is known as plastic shrinkage. It arises either...
Effects of Creep01:25

Effects of Creep

Creep in concrete, the gradual deformation under prolonged stress, significantly impacts the integrity of structures. For reinforced concrete beams, it can be a vital design consideration, as it increases deflection, sometimes necessitating additional design measures. In columns, especially slender ones under eccentric loads, creep can cause buckling, compromising their stability. However, creep can be beneficial in indeterminate structures by mitigating stresses that arise from shrinkage,...
Prestressed Concrete01:20

Prestressed Concrete

Prestressed concrete is a construction technique designed to enhance the strength and durability of concrete structures. This method involves the application of a pre-set tension to high-strength steel strands used as reinforcement before the concrete is subjected to its working loads. The primary aim of prestressing is to place the concrete in a state of compression, in order to counteract the tensile forces it will experience in service. This pre-compression helps prevent crack formation in...
Posttensioned Masonry Walls01:15

Posttensioned Masonry Walls


Post-tensioned masonry walls use high-strength steel rods or flexible tendons to enhance the strength and efficiency of masonry structures. These elements are securely anchored to the foundation and extend vertically either within the cores of the masonry units or between the masonry wythes. The construction process involves building the wall with these tensioning elements in place and allowing the mortar to fully cure.
Following the curing process, the tensioning begins. Steel rods are...
Slump Test01:20

Slump Test

The slump test is a widely used method to measure the workability of concrete. It employs a 12-inch high truncated cone mold that tapers from eight inches at the base to four inches at the top. Before testing, the mold is securely attached to a flat base and dampened.
Concrete is poured into the mold in three layers to conduct the test. Each layer is compacted 25 times with a steel tamping rod, which has a five-eighths-inch diameter and a rounded end, to ensure even distribution and eliminate...
Reinforced Brick Masonry01:15

Reinforced Brick Masonry

Reinforced brick masonry is an advanced construction technique that enhances the structural integrity of brick walls by incorporating steel reinforcements. These reinforcements are either placed within the hollow cores of bricks or sandwiched between two layers of masonry, known as wythes, and are then secured in place with grout. Grout is a fluid mixture composed of Portland cement, aggregate, and water, providing the necessary bonding agent for the steel and brick.
To fortify brick walls...