Related Experiment Video

Updated: Jun 19, 2026

Solid-phase Synthesis of [4.4] Spirocyclic Oximes
05:15

Solid-phase Synthesis of [4.4] Spirocyclic Oximes

Published on: February 6, 2019

Thermal reversion of spirooxazine in ionic liquids containing the [NTf2]- anion

Simon Coleman1, Robert Byrne, Stela Minkovska

  • 1Biomedical Diagnostics Institute, National Centre for Sensor Research, Dublin City, University, Dublin 9, Ireland.

Physical Chemistry Chemical Physics : PCCP
|October 22, 2009
PubMed

More Related Videos

Green Synthesis of Quinoline-Based Ionic Liquid05:59

Green Synthesis of Quinoline-Based Ionic Liquid

Published on: September 27, 2024

Preparation of N-(2-alkoxyvinyl)sulfonamides from N-tosyl-1,2,3-triazoles and Subsequent Conversion to Substituted Phthalans and Phenethylamines10:42

Preparation of N-(2-alkoxyvinyl)sulfonamides from N-tosyl-1,2,3-triazoles and Subsequent Conversion to Substituted Phthalans and Phenethylamines

Published on: January 3, 2018

Related Concept Videos

Thermal Electrocyclic Reactions: Stereochemistry01:17

Thermal Electrocyclic Reactions: Stereochemistry

The stereochemistry of electrocyclic reactions is strongly influenced by the orbital symmetry of the polyene HOMO. Under thermal conditions, the reaction proceeds via the ground-state HOMO.
Selection Rules: Thermal Activation
Conjugated systems containing an even number of π-electron pairs undergo a conrotatory ring closure. For example, thermal electrocyclization of (2E,4E)-2,4-hexadiene, a conjugated diene containing two π-electron pairs, gives trans-3,4-dimethylcyclobutene.
Electrophilic Aromatic Substitution: Fluorination and Iodination of Benzene01:13

Electrophilic Aromatic Substitution: Fluorination and Iodination of Benzene

Bromination and chlorination of aromatic rings by electrophilic aromatic substitution reactions are easily achieved, but fluorination and iodination are difficult to achieve. Fluorine is so reactive that its reaction with benzene is difficult to control, resulting in poor yields of monofluoroaromatic products. To address this, Selectfluor reagent is used as a fluorine source in which a fluorine atom is bonded to a positively charged nitrogen.
Cycloaddition Reactions: MO Requirements for Thermal Activation01:16

Cycloaddition Reactions: MO Requirements for Thermal Activation

Thermal cycloadditions are reactions where the source of activation energy needed to initiate the reaction is provided in the form of heat. A typical example of a thermally-allowed cycloaddition is the Diels–Alder reaction, which is a [4 + 2] cycloaddition. In contrast, a [2 + 2] cycloaddition is thermally forbidden.
Nucleophilic Aromatic Substitution of Aryldiazonium Salts: Aromatic SN101:14

Nucleophilic Aromatic Substitution of Aryldiazonium Salts: Aromatic SN1

Treating arylamines with nitrous acid gives aryldiazonium salts that are effective substrates in nucleophilic aromatic substitution reactions. The diazonio group in these salts can be easily displaced by different nucleophiles, yielding a wide variety of substituted benzenes. The leaving group departs as nitrogen gas, and this easy elimination is the driving force for the substitution reaction.
In the Sandmeyer reaction, for example, the diazonio group is replaced by a chloro, bromo, or cyano...
Thermal and Photochemical Electrocyclic Reactions: Overview01:26

Thermal and Photochemical Electrocyclic Reactions: Overview

Electrocyclic reactions are reversible reactions. They involve an intramolecular cyclization or ring-opening of a conjugated polyene. Shown below are two examples of electrocyclic reactions. In the first reaction, the formation of the cyclic product is favored. In contrast, in the second reaction, ring-opening is favored due to the high ring strain associated with cyclobutene formation.
Radical Halogenation: Thermodynamics01:34

Radical Halogenation: Thermodynamics

The thermodynamic favorability of a reaction is determined by the change in Gibbs free energy (ΔG). ΔG has two components- enthalpy (ΔH) and entropy (ΔS). The entropy component is negligible for alkane halogenation because the number of reactants and product molecules are equal. In this case, the ΔG is governed only by the enthalpy component. The most crucial factor that determines ΔH is the strength of the bonds. ΔH can be determined by comparing the energy between bonds broken and bonds...