Related Experiment Video

Updated: Jun 19, 2026

Measurement of Chitinase Activity in Biological Samples
03:32

Measurement of Chitinase Activity in Biological Samples

Published on: August 22, 2019

Determination of deacetylation degree of chitosan: a comparison between conductometric titration and CHN elemental

Z M Dos Santos1, A L P F Caroni, M R Pereira

  • 1Departamento de Química, Universidade Federal do Rio Grande do Norte, Campus Universitário, Lagoa Nova, Natal, RN 59078-970, Brazil.

Carbohydrate Research
|October 27, 2009
PubMed

More Related Videos

Preparation of Expanded Chitin Foams and their Use in the Removal of Aqueous Copper06:36

Preparation of Expanded Chitin Foams and their Use in the Removal of Aqueous Copper

Published on: February 27, 2021

Capillary Electrophoresis to Monitor Peptide Grafting onto Chitosan Films in Real Time11:05

Capillary Electrophoresis to Monitor Peptide Grafting onto Chitosan Films in Real Time

Published on: October 26, 2016

Related Concept Videos

Conductometric Titrations: Strong Acid-Base and Weak Acid-Base Titrations01:29

Conductometric Titrations: Strong Acid-Base and Weak Acid-Base Titrations

In acid-base titrations, conductance measurements are utilized to detect the endpoint. This method is grounded on the fact that electrical conductance relies on the number and mobility of ions. For instance, consider titrating strong acid HCl with a strong NaOH base. Initially, the HCl in the conductivity vessel conducts electricity due to the presence of hydrogen ions and chloride ions. As NaOH is gradually added from the burette, the fast-moving hydrogen ions are replaced by slower-moving...
Solution Composition During Acid/Base Titrations01:17

Solution Composition During Acid/Base Titrations

The titration of a weak acid with a strong base results in the formation of water and the conjugate base of the acid. For instance, titrating acetic acid with sodium hydroxide leads to the formation of water and sodium acetate. A solution of acetic acid and sodium acetate constitutes a buffer whose relative concentration at different stages of the titration is indicated by the α values, which represent percentages of the weak acid and its conjugate base.
The α0 and α1 values represent the...
Conductometric Titrations: Strong Acid-Weak Base and Weak Acid-Strong Base Titrations01:22

Conductometric Titrations: Strong Acid-Weak Base and Weak Acid-Strong Base Titrations

When a weak acid such as acetic acid is titrated against a strong base like sodium hydroxide, the initial conductance is relatively low due to the weak dissociation of acetic acid. However, as sodium hydroxide is added to the solution, it reacts with the acetic acid to produce highly ionized sodium acetate, which causes an increase in conductance. Once all the acetic acid has been neutralized, any additional sodium hydroxide introduces fast-moving hydroxyl ions, leading to a sharper increase in...
Precipitation Titration: Endpoint Detection Methods01:19

Precipitation Titration: Endpoint Detection Methods

In argentometric precipitation titrations, endpoints can be detected visually by the Mohr, Volhard, and Fajans methods. In the Mohr method, adding a soluble chromate indicator gives an initial yellow color to the analyte solution. As the titrant is added, the first excess of silver ions forms a red silver chromate precipitate, marking the endpoint. The solution pH should be maintained at about 8 by adding solid CaCO3.
In the Volhard method, a standard excess of AgNO3 is first added to the...
Titration Calculations: Weak Acid - Strong Base03:55

Titration Calculations: Weak Acid - Strong Base

Calculating pH for Titration Solutions: Weak Acid/Strong Base
For the titration of 25.00 mL of 0.100 M CH3CO2H with 0.100 M NaOH, the reaction can be represented as:
Effects of EDTA on End-Point Detection Methods01:18

Effects of EDTA on End-Point Detection Methods

Different methods, such as visual observance of metal-ion indicators, spectroscopic techniques, and potentiometric methods, can determine the endpoint of an EDTA titration.
In the visual method, metal-ion indicators (metallochromic dyes), which have distinct colors in their free and complex forms, are added to the mixture to signal the titration's end point. They form stable complexes with metal ions, but these complexes are weaker than the corresponding metal–EDTA complexes. As a result, EDTA...