Related Experiment Video

Updated: Jun 19, 2026

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition
05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

Theoretical and experimental comparison of an adjustable Y-junction switch

T C Huang, G J Simonis, V R Chinni

    Optics Letters
    |October 27, 2009
    PubMed

    More Related Videos

    Measuring Light-Switching Behavior Using an Occupancy and Light Data Logger05:50

    Measuring Light-Switching Behavior Using an Occupancy and Light Data Logger

    Published on: January 16, 2020

    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators11:44

    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

    Published on: August 15, 2014

    Related Concept Videos

    Switching of BJT01:22

    Switching of BJT

    Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
    Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are reverse-biased. The...
    The Y-to-Y Circuit01:19

    The Y-to-Y Circuit

    In a balanced four-wire wye-to-wye system, the arrangement involves wye-connected sinusoidal voltage sources and loads, connected through a neutral wire that links the neutral nodes of the source and load. The load impedance is connected across each phase of the load. The wye-connected source can be connected to the wye-connected load in four-wire and three-wire arrangements. A three-phase system is considered balanced when the load on each phase is equal, leading to uniform current flow and...
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    Comparison between RL and RC circuits01:24

    Comparison between RL and RC circuits

    An RC circuit consists of resistance and capacitance, while in an RL circuit, capacitance is replaced by an inductor. RL and RC circuits are first-order differential circuits that store energy. An RC circuit stores energy in the electric field, while an RL circuit stores energy in the magnetic field. When connected to a battery, an RC circuit charges the capacitor, causing the current to decrease from maximum to zero upon being fully charged. This increases the voltage across the capacitor from...
    Biasing of P-N Junction01:16

    Biasing of P-N Junction

    The operation of a p-n junction diode involves various biasing conditions, including forward bias, reverse bias, and equilibrium.
    In equilibrium, no external voltage is applied across the p-n junction. The depletion region is formed at the junction interface due to the diffusion of carriers, which leaves behind charged dopants, acceptors on the p-side, and donors on the n-side. These immobile charges create an electric field that prevents further diffusion of carriers. The related energy band...
    The Y-to-Delta Circuit01:19

    The Y-to-Delta Circuit

    A balanced wye-to-delta circuit comprises balanced Y-connected voltage sources and delta-connected loads with no neutral line connection.
    The initial step in analyzing a wye-to-delta circuit is to assume a positive phase sequence. These phase voltages are then utilized to calculate the line voltages that occur directly across the delta-connected load impedances. Van, Vbn, and Vcn are the phase voltages in wye, and Vab, Vbc, and Vca are the line voltages for a delta circuit. The relation between...