Related Experiment Video

Updated: Jun 18, 2026

Biocontained Carcass Composting for Control of Infectious Disease Outbreak in Livestock
14:34

Biocontained Carcass Composting for Control of Infectious Disease Outbreak in Livestock

Published on: May 6, 2010

Characterization of bulking agents and its effects on physical properties of compost

Muhammad Khalid Iqbal1, Tahira Shafiq, Khurshed Ahmed

  • 1CEPS, PCSIR Laboratories Complex, Lahore, Punjab, Pakistan. khalid_khichi2000@yahoo.com

Bioresource Technology
|November 17, 2009
PubMed

More Related Videos

Physical, Chemical and Biological Characterization of Six Biochars Produced for the Remediation of Contaminated Sites09:39

Physical, Chemical and Biological Characterization of Six Biochars Produced for the Remediation of Contaminated Sites

Published on: November 28, 2014

A Plate Competition Assay As a Quick Preliminary Assessment of Disease Suppression05:23

A Plate Competition Assay As a Quick Preliminary Assessment of Disease Suppression

Published on: October 28, 2018

Related Concept Videos

Moisture Content and Bulking of Aggregate01:10

Moisture Content and Bulking of Aggregate

The moisture content of aggregates is a crucial factor in construction, particularly in concrete mixing, as it influences the total water required in the mix. Moisture content represents the water coated on the exterior surface of the aggregate existing in a saturated and surface-dry condition. The total water content of a moist aggregate is the sum of its moisture content and water absorption.
When aggregates are exposed to rain or sit in stockpiles, they absorb moisture, which must be...
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
Additives and Fillers in Concrete01:29

Additives and Fillers in Concrete

Additives and fillers are integral to enhancing the properties of concrete. Pozzolans and blast-furnace slag are additives or admixtures due to their reactions with calcium hydroxide released during cement hydration. Fillers, which are finely ground and similar in fineness to Portland cement, improve concrete attributes such as workability density, and reduce capillary bleeding or cracking. Some fillers possess hydraulic properties or participate in benign reactions within the cement paste.
The...
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
Drugs Affecting GI Tract Motility: Bulk-Forming and Stimulant Laxatives01:22

Drugs Affecting GI Tract Motility: Bulk-Forming and Stimulant Laxatives

Laxatives enhance bowel movements and alleviate constipation. They augment the stool's bulk, stimulate intestinal muscle contractions, draw water into the intestines, or soften the stool. There are five key types of laxatives: bulk laxatives, stimulant laxatives, osmotic laxatives, stool softeners, and lubricant laxatives.
Bulk-forming laxatives, such as psyllium, methylcellulose, and polycarbophil, absorb water in the intestine, increasing stool bulk and promoting bowel movement. This makes...
Bulk Modulus01:21

Bulk Modulus

The bulk modulus is a scientific term used to describe a material's resistance to uniform compression. It is the proportionality constant that links a change in pressure to the resulting relative volume change.