Jove
Visualize
Contact Us
JoVE
x logofacebook logolinkedin logoyoutube logo
ABOUT JoVE
OverviewLeadershipBlogJoVE Help Center
AUTHORS
Publishing ProcessEditorial BoardScope & PoliciesPeer ReviewFAQSubmit
LIBRARIANS
TestimonialsSubscriptionsAccessResourcesLibrary Advisory BoardFAQ
RESEARCH
JoVE JournalMethods CollectionsJoVE Encyclopedia of ExperimentsArchive
EDUCATION
JoVE CoreJoVE BusinessJoVE Science EducationJoVE Lab ManualFaculty Resource CenterFaculty Site
Terms & Conditions of Use
Privacy Policy
Policies

Related Concept Videos

Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
Steady, Laminar Flow Between Parallel Plates01:17

Steady, Laminar Flow Between Parallel Plates

Understanding steady, laminar flow between parallel plates is essential for analyzing and designing flow in narrow rectangular channels, commonly found in various water conveyance and drainage systems. The Navier-Stokes equations govern fluid motion and are generally challenging to solve due to their nonlinearity. However, simplifications are possible in certain cases, like the steady laminar flow between parallel plates. For this scenario, we assume steady, incompressible, laminar flow.
Tangent Planes to Level Surfaces01:31

Tangent Planes to Level Surfaces

A level surface consists of all points in space where a function of three variables takes the same fixed value. If a point lies on this surface, understanding the surface’s geometry there requires more than just knowing the point’s coordinates; it requires describing how the surface is oriented, or how it tilts, near that point.To probe this local geometry, imagine tracing a path that stays entirely on the level surface and passes through the point of interest. This path can be described as a...
Oriented Surfaces01:30

Oriented Surfaces

A surface is called orientable if a consistent choice of unit normal vector can be made at every point on the surface. A thin soap film stretched across a wire loop provides a familiar example. The film separates the air on one side from the air on the other, so one side can be selected as positive and the opposite side as negative. Once this choice is made, a unit normal vector can be assigned smoothly across the entire surface.At each point on the soap film, a unit normal vector points...

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by
Same author

The WHO 2016 diagnostic criteria for Acute Myeloid leukemia with myelodysplasia related changes (AML-MRC) produce a very heterogeneous entity: A retrospective analysis of the FAB subtype RAEB-T.

Leukemia research·2021
Same author

A Case of Acute Eosinophilic Leukemia with a Novel <i>PHF</i>6 Mutation.

Case reports in hematology·2021
Same author

A case of Burkitt Leukemia: Revisiting the prognostic value of lactate dehydrogenase.

Leukemia research·2020
Same author

Publisher Correction: GloPL, a global data base on pollen limitation of plant reproduction.

Scientific data·2019
Same author

GloPL, a global data base on pollen limitation of plant reproduction.

Scientific data·2018
Same author

Smokers Display Reduced Glucocorticoid Sensitivity Prior to Symptomatic Chronic Disease Development.

Annals of behavioral medicine : a publication of the Society of Behavioral Medicine·2018

Related Experiment Video

Updated: Jun 17, 2026

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats &amp; Spheres
13:07

Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

Published on: December 1, 2014

Bowl feed technique for producing supersmooth optical surfaces

R W Dietz, J M Bennett

    Applied Optics
    |January 6, 2010
    PubMed
    Summary

    No abstract available in PubMed .

    More Related Videos

    Fabrication and Operation of a Nano-Optical Conveyor Belt
    11:10

    Fabrication and Operation of a Nano-Optical Conveyor Belt

    Published on: August 26, 2015

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry
    12:14

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

    Published on: August 12, 2013

    Related Experiment Videos

    Last Updated: Jun 17, 2026

    Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats &amp; Spheres
    13:07

    Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

    Published on: December 1, 2014

    Fabrication and Operation of a Nano-Optical Conveyor Belt
    11:10

    Fabrication and Operation of a Nano-Optical Conveyor Belt

    Published on: August 26, 2015

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry
    12:14

    The Generation of Higher-order Laguerre-Gauss Optical Beams for High-precision Interferometry

    Published on: August 12, 2013