Related Experiment Video

Updated: Jun 17, 2026

Methods of Soil Resampling to Monitor Changes in the Chemical Concentrations of Forest Soils
09:16

Methods of Soil Resampling to Monitor Changes in the Chemical Concentrations of Forest Soils

Published on: November 25, 2016

[Splash erosion of black soil with different reclamation years and its relations to soil aggregates selective

Yi-Yang Zhou1, En-Heng Wang, Xiang-Wei Chen

  • 1School of Forestry, Northeast Forestry University, Harbin 150040, China. zyy82150426@163.com

Ying Yong Sheng Tai Xue Bao = the Journal of Applied Ecology
|January 19, 2010
PubMed

More Related Videos

Use of Principal Components for Scaling Up Topographic Models to Map Soil Redistribution and Soil Organic Carbon09:44

Use of Principal Components for Scaling Up Topographic Models to Map Soil Redistribution and Soil Organic Carbon

Published on: October 16, 2018

Measuring and Mapping Patterns of Soil Erosion and Deposition Related to Soil Carbonate Concentrations Under Agricultural Management08:09

Measuring and Mapping Patterns of Soil Erosion and Deposition Related to Soil Carbonate Concentrations Under Agricultural Management

Published on: September 12, 2017

Related Concept Videos

Unsoundness of Aggregate due to Volume Change01:26

Unsoundness of Aggregate due to Volume Change

Unsoundness in aggregates due to volume changes is primarily caused by the physical alterations aggregates undergo, such as freezing and thawing, thermal changes, and wetting and drying. Unsound aggregates, when subjected to these changes, result in volume change upon disintegration. This, in turn, contributes to the deterioration of concrete, including scaling, pop-outs, and cracking. Particular types of aggregates, such as porous flints, cherts, and those containing clay minerals, are...
Deleterious Substances in Aggregate01:25

Deleterious Substances in Aggregate

Deleterious substances in aggregates can be detrimental to the quality and durability of concrete. These substances include organic impurities like loam, which interfere with cement hydration and are usually present in the sand. These prevent a good bond between aggregate and cement paste. Organic impurities can be detected using the colorimetric test, where the darkness of a solution after agitation indicates the level of organic content.
Another type of impurity is clay and fine material that...
Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is sampled...
Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...
Aggregates Classification01:29

Aggregates Classification

Aggregate classification is generally based on its size, petrographic characteristics, weight, and source. Size classification ranges from coarse to fine aggregates, defined by the size of the particles. Coarse aggregates are particles that do not pass through ASTM sieve No. 4, and aggregates that pass through the sieve are fine aggregates.
Petrographic classification groups aggregates based on common mineralogical characteristics. Some of the common mineral groups found in aggregates are...