Related Experiment Video

Updated: Jun 16, 2026

Stimulated Stokes and Antistokes Raman Scattering in Microspherical Whispering Gallery Mode Resonators
12:21

Stimulated Stokes and Antistokes Raman Scattering in Microspherical Whispering Gallery Mode Resonators

Published on: April 4, 2016

Band splitting and modal dispersion induced by symmetry braking in coupled-resonator slowlight waveguide structures

J Scheuer1, M Shtaif

  • 1Department of Electrical Engineering, Tel Aviv University, Tel Aviv, Israel. kobys@eng.tau.ac.il

Optics Express
|February 23, 2010
PubMed

More Related Videos

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

Related Concept Videos

IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations01:08

IR Spectrum Peak Splitting: Symmetric vs Asymmetric Vibrations

Identical bonds within a polyatomic group can stretch symmetrically (in-phase) or asymmetrically (out-of-phase). Similar to hydrogen bonding, these vibrations also influence the shape of the IR peak. Generally, asymmetric stretching frequencies are higher than symmetric stretching frequencies. For example, primary amines exhibit two distinct IR peaks between 3300–3500 cm−1 corresponding to the symmetric and asymmetric N-H stretching, while secondary amines exhibit a single stretching vibration...
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
Sound Waves: Resonance01:14

Sound Waves: Resonance

Resonance is produced depending on the boundary conditions imposed on a wave. Resonance can be produced in a string under tension with symmetrical boundary conditions (i.e., has a node at each end). A node is defined as a fixed point where the string does not move. The symmetrical boundary conditions result in some frequencies resonating and producing standing waves, while other frequencies interfere destructively. Sound waves can resonate in a hollow tube, and the frequencies of the sound...
Modes of Standing Waves: II01:04

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end.
Characteristics of Series Resonant Circuit01:24

Characteristics of Series Resonant Circuit

Series resonance occurs in a circuit containing inductive (L), capacitive (C), and resistive (R) elements connected sequentially. At the resonance frequency, the inductive and capacitive reactances are equal in magnitude but opposite in sign, effectively canceling each other. This causes the circuit's impedance is minimal, primarily determined by the resistance R. The resonant frequency of an RLC circuit is defined as:
¹H NMR: Complex Splitting01:13

¹H NMR: Complex Splitting

A proton M that is coupled to a proton X results in doublet signals for M. However, NMR-active nuclei can be simultaneously coupled to more than one nonequivalent nucleus. When M is coupled to a second proton A, such as in styrene oxide, each peak in the doublet is split into another doublet.
Splitting diagrams or splitting tree diagrams are routinely used to depict such complex couplings. While drawing splitting diagrams, the splitting with the larger coupling constant is usually applied first.