Related Experiment Video

Updated: Jun 12, 2026

Using Microwave and Macroscopic Samples of Dielectric Solids to Study the Photonic Properties of Disordered Photonic Bandgap Materials
10:35

Using Microwave and Macroscopic Samples of Dielectric Solids to Study the Photonic Properties of Disordered Photonic Bandgap Materials

Published on: September 26, 2014

Analytical expression of giant Goos-Hänchen shift in terms of proper and improper modes in waveguide structures with

Fatemeh Alishahi1, Khashayar Mehrany

  • 1Department of Electrical Engineering, Sharif University of Technology, Tehran, Iran.

Optics Letters
|June 3, 2010
PubMed

More Related Videos

Interfacial Molecular-level Structures of Polymers and Biomacromolecules Revealed via Sum Frequency Generation Vibrational Spectroscopy09:43

Interfacial Molecular-level Structures of Polymers and Biomacromolecules Revealed via Sum Frequency Generation Vibrational Spectroscopy

Published on: August 13, 2019

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

Related Concept Videos

Modes of Standing Waves: II01:04

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end.
Traveling Waves: Lossless Lines01:27

Traveling Waves: Lossless Lines

The provided content explores the behavior of traveling waves on single-phase lossless transmission lines. It begins with a single-phase two-wire lossless transmission line of length Δx, characterized by a loop inductance LH/m and a line-to-line capacitance C F/m. These parameters result in a series inductance LΔx and a shunt capacitance CΔx.
Propagation of Waves01:07

Propagation of Waves

When a wave propagates from one medium to another, part of it may get reflected in the first medium, and part of it may get transmitted to the second medium. In such a case, the interface of the two mediums can be considered as a boundary that is neither fixed nor free.
Consider a scenario where a wave propagates from a string of low linear mass density to a string of high linear mass density. In such a case, the reflected wave is out of phase with respect to the incident wave, however the...
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
Hyperbolic and Inverse Hyperbolic Functions: Problem Solving01:30

Hyperbolic and Inverse Hyperbolic Functions: Problem Solving

An arched gate can be effectively modeled using a hyperbolic cosine profile because this type of function is smooth and symmetric about the vertical axis. When the arch is centered at the origin, its maximum height occurs at the center point. This symmetry ensures that any height below the crown of the arch is reached at two horizontal positions that are equal in distance from the centerline but lie on opposite sides.To determine where the gate reaches a height of five meters, the height of the...
Singularity Functions for Bending Moment01:18

Singularity Functions for Bending Moment

Singularity functions simplify the representation of bending moments in beams subjected to discontinuous loading, allowing the use of a single mathematical expression. For a supported beam AB, with uniform loading from its midpoint M to the right side end B, the approach involves conceptual 'cuts' at specific points to determine the bending moment in each segment. By cutting the beam at a point between A and M, the bending moment for the segment before reaching midpoint M is represented using a...