Related Experiment Video

Updated: Jun 10, 2026

Measuring the Complete-arch Distortion of an Optical Dental Impression
06:51

Measuring the Complete-arch Distortion of an Optical Dental Impression

Published on: May 30, 2019

Accurate measurement of the dihedral angle of a corner cube

C Ai, K L Smith

    Applied Optics
    |August 20, 2010
    PubMed

    More Related Videos

    Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid08:58

    Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

    Published on: December 2, 2022

    Accuracy in Dental Medicine, A New Way to Measure Trueness and Precision07:57

    Accuracy in Dental Medicine, A New Way to Measure Trueness and Precision

    Published on: April 29, 2014

    Related Concept Videos

    Accuracy, limits, and approximation01:28

    Accuracy, limits, and approximation

    Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a given value is as close as possible to its true value.
    Accuracy is defined as the closeness of the measured value to the true or actual value. In engineering mechanics, repeated measurements are taken during theoretical or experimental analyses to ensure that the result is precise and accurate.
    The accuracy of any solution is based on the...
    Adjusting a Traverse01:12

    Adjusting a Traverse

    In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
    Unsymmetric Bending - Angle of Neutral Axis01:15

    Unsymmetric Bending - Angle of Neutral Axis

    Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
    When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal centroidal axes. The...
    Angle of Twist: Problem Solving01:13

    Angle of Twist: Problem Solving

    An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...
    Design Example: Traverse Angle Computations01:25

    Design Example: Traverse Angle Computations

    Traverse angle computations are a critical component of surveying, used to compute the internal angles within a closed traverse. A traverse consists of a series of connected lines forming a closed loop, often used for land boundary delineation or mapping. Calculating the internal angles ensures accuracy in the traverse geometry and is essential for checking survey data integrity.The process begins with known azimuths and bearings of the traverse sides. Internal angles at each vertex are...
    Optimization Problems01:26

    Optimization Problems

    Optimization problems often involve identifying maximum or minimum values under specific constraints. A well-known example is determining the longest horizontal pipe that can be moved around a right-angled corner, where a 3-meter-wide hallway meets a 2-meter-wide hallway. This scenario, common in architectural design and industrial transport, can be understood conceptually through geometric and trigonometric reasoning.To visualize the problem, consider the pipe as a straight line that touches...