Related Experiment Video

Updated: Jun 8, 2026

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities
11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

Second-order perturbation theory of rectangular waveguides and directional couplers

B Costantini, C De Angelis, A Galtarossa

    Applied Optics
    |September 24, 2010
    PubMed

    More Related Videos

    Terahertz Microfluidic Sensing Using a Parallel-plate Waveguide Sensor07:28

    Terahertz Microfluidic Sensing Using a Parallel-plate Waveguide Sensor

    Published on: August 30, 2012

    Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

    Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

    Published on: August 5, 2013

    Related Concept Videos

    Second-order Op Amp Circuits01:19

    Second-order Op Amp Circuits

    Implementing second-order low-pass filters in audio systems is crucial in refining audio signals by eliminating undesirable high-frequency noise. These filters typically involve second-order op-amp circuits configured as voltage followers, encompassing two nodes with distinct storage elements.
    The analysis of such circuits follows a systematic approach, similar to the second-order RLC circuits. In practical scenarios, bulky inductors are rarely employed due to their size and weight. This means...
    Second-Order Circuits01:17

    Second-Order Circuits

    Integrating two fundamental energy storage elements in electrical circuits results in second-order circuits, encompassing RLC circuits and circuits with dual capacitors or inductors (RC and RL circuits). Second-order circuits are identified by second-order differential equations that link input and output signals.
    Input signals typically originate from voltage or current sources, with the output often representing voltage across the capacitor and/or current through the inductor. For example, in...
    Standing Waves in a Cavity01:28

    Standing Waves in a Cavity

    A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
    Traveling Waves: Lossless Lines01:27

    Traveling Waves: Lossless Lines

    The provided content explores the behavior of traveling waves on single-phase lossless transmission lines. It begins with a single-phase two-wire lossless transmission line of length Δx, characterized by a loop inductance LH/m and a line-to-line capacitance C F/m. These parameters result in a series inductance LΔx and a shunt capacitance CΔx.
    Modes of Standing Waves: II01:04

    Modes of Standing Waves: II

    The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
    For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end.
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    If  ζ...