Related Experiment Video

Updated: Jun 8, 2026

Optical Scatter Microscopy Based on Two-Dimensional Gabor Filters
14:58

Optical Scatter Microscopy Based on Two-Dimensional Gabor Filters

Published on: June 2, 2010

Admittance of rugate filters derived from a 2 × 2 inhomogeneous matrix

F Villa, R Machorro, J Siqueiros

    Applied Optics
    |October 2, 2010
    PubMed

    More Related Videos

    Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns13:44

    Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns

    Published on: August 30, 2013

    2D and 3D Matrices to Study Linear Invadosome Formation and Activity12:25

    2D and 3D Matrices to Study Linear Invadosome Formation and Activity

    Published on: June 2, 2017

    Related Concept Videos

    Routh-Hurwitz Criterion II01:19

    Routh-Hurwitz Criterion II

    In the application of the Routh-Hurwitz criterion, two specific scenarios can arise that complicate stability analysis.
    The first scenario occurs when a singular zero appears in the first column of the Routh table. This situation creates a division by zero issues. To resolve this, a small positive or negative number, denoted as epsilon (∈), is substituted for the zero. The stability analysis proceeds by assuming a sign for ∈. If ∈ is positive, any sign change in the first column of the Routh...
    Convolution: Math, Graphics, and Discrete Signals01:24

    Convolution: Math, Graphics, and Discrete Signals

    In any LTI (Linear Time-Invariant) system, the convolution of two signals is denoted using a convolution operator, assuming all initial conditions are zero. The convolution integral can be divided into two parts: the zero-input or natural response and the zero-state or forced response, with t0 indicating the initial time.
    To simplify the convolution integral, it is assumed that both the input signal and impulse response are zero for negative time values. The graphical convolution process...
    Active Filters01:25

    Active Filters

    Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
    Vector Algebra: Method of Components01:08

    Vector Algebra: Method of Components

    It is cumbersome to find the magnitudes of vectors using the parallelogram rule or using the graphical method to perform mathematical operations like addition, subtraction, and multiplication. There are two ways to circumvent this algebraic complexity. One way is to draw the vectors to scale, as in navigation, and read approximate vector lengths and angles (directions) from the graphs. The other way is to use the method of components.
    In many applications, the magnitudes and directions of...
    Multi-input and Multi-variable systems01:22

    Multi-input and Multi-variable systems

    Cruise control systems in cars are designed as multi-input systems to maintain a driver's desired speed while compensating for external disturbances such as changes in terrain. The block diagram for a cruise control system typically includes two main inputs: the desired speed set by the driver and any external disturbances, such as the incline of the road. By adjusting the engine throttle, the system maintains the vehicle's speed as close to the desired value as possible.
    In the absence of...
    Bus Impedance Matrix01:24

    Bus Impedance Matrix

    Calculating subtransient fault currents for three-phase faults in an N-bus power system involves using the positive-sequence network. When a three-phase short circuit occurs at a specific bus, the analysis uses the superposition method to evaluate two separate circuits.
    In the first circuit, all machine voltage sources are short-circuited, leaving only the prefault voltage source at the fault location. The positive-sequence bus impedance matrix can be determined by solving the nodal equations,...