Related Experiment Video

Updated: Jun 7, 2026

Agarose-based Tissue Mimicking Optical Phantoms for Diffuse Reflectance Spectroscopy
09:25

Agarose-based Tissue Mimicking Optical Phantoms for Diffuse Reflectance Spectroscopy

Published on: August 22, 2018

Diffuse reflectance and transmittance spectra of an interference layer: 1. Model formulation and properties

A Roos, D Rönnow

    Applied Optics
    |October 22, 2010
    PubMed

    More Related Videos

    Interfacial Molecular-level Structures of Polymers and Biomacromolecules Revealed via Sum Frequency Generation Vibrational Spectroscopy09:43

    Interfacial Molecular-level Structures of Polymers and Biomacromolecules Revealed via Sum Frequency Generation Vibrational Spectroscopy

    Published on: August 13, 2019

    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers13:44

    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers

    Published on: December 27, 2012

    Related Concept Videos

    Interference and Diffraction02:18

    Interference and Diffraction

    Interference is a characteristic phenomenon exhibited by waves. When two electromagnetic waves interact with their peaks and troughs coinciding, a resulting wave with enhanced amplitude is produced. This is known as constructive interference. In this case, the two waves interacting are in phase with each other.
    Attenuated Total Reflectance (ATR) Infrared Spectroscopy: Overview01:13

    Attenuated Total Reflectance (ATR) Infrared Spectroscopy: Overview

    Attenuated total reflectance (ATR) infrared spectroscopy is a powerful analytical technique used to study the composition of materials. It is widely employed in chemistry, materials science, forensic science, and other fields where sample characterization is required. ATR has several advantages over traditional transmission IR spectroscopy, including the requirement of little to no sample preparation and the ability to analyze a wide range of samples.
    The ATR process begins by directing a beam...
    Atomic Absorption Spectroscopy: Interference01:25

    Atomic Absorption Spectroscopy: Interference

    Interference leads to systematic error in atomic absorption (AA) measurements by enhancing or diminishing the analytical signal or the background. These interferences can be grouped into three main categories: spectral interference, chemical interference, and physical interference.
    Spectral interference occurs when signals from other elements or molecules overlap with the analyte signal, falsely elevating or masking the analyte's absorbance. This interference can be corrected using Zeeman,...
    Spectrophotometry: Introduction01:16

    Spectrophotometry: Introduction

    Spectrophotometry is the quantitative measurement of the absorption, reflection, diffraction, or transmission of electromagnetic radiation through a material as a function of the intensity and wavelength of the radiation. A spectrophotometer is a device used to measure the change in the radiation intensity caused by its interaction with the material.
    The essential components of a spectrophotometer include a source of electromagnetic radiation, a slot for placing a material to be analyzed, and a...
    IR Spectrum01:19

    IR Spectrum

    When infrared (IR) radiation passes through a molecule, the bonds stretch or bend by absorbing the radiation. This absorption creates the molecule's absorption spectrum, which is the plot of its percentage transmittance versus wavenumber.
    Transmittance is defined as the ratio of the radiant power passing through a sample to that from the radiation's source. Multiplying the transmittance by 100 gives the percent transmittance (%T), which varies between 100% (no absorption) and 0% (complete...
    Atomic Emission Spectroscopy: Interference01:30

    Atomic Emission Spectroscopy: Interference

    In atomic emission spectroscopy (AES), high-temperature atomizers excite a broad range of elements and molecules that generate complex emissions from sources such as oxides, hydroxides, and flame combustion products in the flame or plasma. Several strategies can be employed to minimize spectral interferences caused by overlapping emission lines or bands. These include increasing instrument resolution, choosing alternative emission lines, optimally placing the detector in low-background regions,...