Related Experiment Video

Updated: Jun 6, 2026

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications
11:20

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications

Published on: August 15, 2018

Heat of freezing for supercooled water: measurements at atmospheric pressure

Will Cantrell1, Alexander Kostinski, Anthony Szedlak

  • 1Department of Physics, Michigan Technological University, Houghton, Michigan, USA. cantrell@mtu.edu

The Journal of Physical Chemistry. A
|November 20, 2010
PubMed

More Related Videos

Protocol for Measuring the Thermal Properties of a Supercooled Synthetic Sand-water-gas-methane Hydrate Sample09:46

Protocol for Measuring the Thermal Properties of a Supercooled Synthetic Sand-water-gas-methane Hydrate Sample

Published on: March 21, 2016

Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures09:50

Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures

Published on: June 28, 2017

Related Concept Videos

Freezing Point Depression and Boiling Point Elevation03:12

Freezing Point Depression and Boiling Point Elevation

Boiling Point Elevation
The boiling point of a liquid is the temperature at which its vapor pressure is equal to ambient atmospheric pressure. Since the vapor pressure of a solution is lowered due to the presence of nonvolatile solutes, it stands to reason that the solution’s boiling point will subsequently be increased. Vapor pressure increases with temperature, and so a solution will require a higher temperature than will pure solvent to achieve any given vapor pressure, including one...
Freezing Point Depression and Boiling Point Elevation01:24

Freezing Point Depression and Boiling Point Elevation

When a non-volatile solute is added to a pure solvent, it results in the lowering of the freezing point of the solvent. This phenomenon is called freezing point depression. The extent to which the freezing point is lowered depends on the molality of the solute -the number of moles of solute per kilogram of solvent and the cryoscopic constant of the solvent.From the plot of chemical potential, μ, against temperature, it is evident that the μ of both solid and liquid solvents decrease with...
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
Phase Diagram01:24

Phase Diagram

A phase diagram is a graphical representation of the physical states of a substance under different conditions of temperature and pressure. It shows the boundaries between solid, liquid, and gas phases and the conditions at which these phases coexist in equilibrium. An area in a phase diagram represents a single phase, whereas lines or phase boundaries represent the equilibrium between two phases.In the phase diagram of water, the boundary line between the solid and liquid states illustrates...