Related Experiment Video

Updated: Jun 1, 2026

Determining the Mechanical Strength of Ultra-Fine-Grained Metals
05:04

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

Published on: November 22, 2021

Effect of the interparticle potential on the yield stress of amorphous solids

Smarajit Karmakar1, Edan Lerner, Itamar Procaccia

  • 1Department of Chemical Physics, The Weizmann Institute of Science, Rehovot 76100, Israel.

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|May 24, 2011
PubMed

More Related Videos

Stress Distribution During Cold Compression of Rocks and Mineral Aggregates Using Synchrotron-based X-Ray Diffraction10:36

Stress Distribution During Cold Compression of Rocks and Mineral Aggregates Using Synchrotron-based X-Ray Diffraction

Published on: May 20, 2018

Probing C84-embedded Si Substrate Using Scanning Probe Microscopy and Molecular Dynamics13:58

Probing C84-embedded Si Substrate Using Scanning Probe Microscopy and Molecular Dynamics

Published on: September 28, 2016

Related Concept Videos

Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and reloaded.
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as the...
Elastic Strain Energy for Shearing Stresses01:20

Elastic Strain Energy for Shearing Stresses

As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
Problem Solving on Stress and Strain01:22

Problem Solving on Stress and Strain

Stress is a quantity that describes the magnitude of a force that causes deformation, generally defined as internal force per unit area. When forces pull on an object and cause its elongation, like the stretching of an elastic band, it is called tensile stress. When forces cause the compression of an object, it is known as compressive stress. When an object is being squeezed uniformly from all sides, like a submarine in the depths of the ocean, we call this kind of stress bulk stress (or volume...
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
Stress-Strain Diagram - Ductile Materials01:24

Stress-Strain Diagram - Ductile Materials

The stress-strain relationship in ductile materials such as structural steel or aluminium is intricate and progresses through several stages. When a specimen is loaded, it initially exhibits a linear length increase, depicted by a steep straight line on the stress-strain diagram. It indicates the material is elastically deforming and will return to its original shape once unloaded. However, when a critical stress value is reached, plastic deformation begins. This stage sees substantial...