Related Experiment Video

Updated: May 31, 2026

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method
07:37

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method

Published on: January 16, 2019

Asymptotic analysis of stresses near a crack tip in a two-dimensional colloidal packing saturated with liquid

Arijit Sarkar1, Mahesh S Tirumkudulu

  • 1Department of Chemical Engineering, Indian Institute of Technology Bombay, Powai, Mumbai, India. arijit@che.iitb.ac.in

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|July 7, 2011
PubMed

More Related Videos

Stress Distribution During Cold Compression of Rocks and Mineral Aggregates Using Synchrotron-based X-Ray Diffraction10:36

Stress Distribution During Cold Compression of Rocks and Mineral Aggregates Using Synchrotron-based X-Ray Diffraction

Published on: May 20, 2018

Confocal Imaging of Confined Quiescent and Flowing Colloid-polymer Mixtures10:56

Confocal Imaging of Confined Quiescent and Flowing Colloid-polymer Mixtures

Published on: May 20, 2014

Related Concept Videos

Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
Components of Stress01:23

Components of Stress

Stress analysis under multiple loading conditions is intricate, necessitating a comprehensive grasp of normal and shearing stresses. Consider a small cube at point O, subjected to stress on all six faces, visible or not. Normal stress components σx, σy, σz act perpendicularly to the x, y, and z axes. Shearing stress components τxy and τxz are exerted on faces perpendicular to these axes.
Interestingly, the hidden cube faces also experience these stresses, equal and opposite to those on the...
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...