Related Experiment Video

Updated: May 31, 2026

Precision Milling of Carbon Nanotube Forests Using Low Pressure Scanning Electron Microscopy
08:10

Precision Milling of Carbon Nanotube Forests Using Low Pressure Scanning Electron Microscopy

Published on: February 5, 2017

The constitutive relation and small scale parameter of nonlocal continuum mechanics for modelling carbon nanotubes

Q Wang1, C M Wang

  • 1Department of Mechanical and Manufacturing Engineering, University of Manitoba, Winnipeg, Manitoba, R3T 5V6, Canada.

Nanotechnology
|July 7, 2011
PubMed

More Related Videos

DNA Nanotubes as a Versatile Tool to Study Semiflexible Polymers08:00

DNA Nanotubes as a Versatile Tool to Study Semiflexible Polymers

Published on: October 25, 2017

Fabrication, Densification, and Replica Molding of 3D Carbon Nanotube Microstructures09:23

Fabrication, Densification, and Replica Molding of 3D Carbon Nanotube Microstructures

Published on: July 2, 2012

Related Concept Videos

Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
Generalized Hooke's Law01:22

Generalized Hooke's Law

The generalized Hooke's Law is a broadened version of Hooke's Law, which extends to all types of stress and in every direction. Consider an isotropic material shaped into a cube subjected to multiaxial loading. In this scenario, normal stresses are exerted along the three coordinate axes. As a result of these stresses, the cubic shape deforms into a rectangular parallelepiped. Despite this deformation, the new shape maintains equal sides, and there is a normal strain in the direction of the...
Indeterminate Structure01:18

Indeterminate Structure

Indeterminate structures refer to structures where internal forces and reactions cannot be determined using only the equations of static equilibrium.  Indeterminate structures have more unknown forces and reaction forces than equations of static equilibrium that can be used to determine them. Indeterminate structures are often used in engineering to create complex, efficient, and aesthetically pleasing structures. There are various types of indeterminate structures used in engineering and some...
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...