Related Experiment Video

Updated: May 30, 2026

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section
11:00

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section

Published on: July 19, 2016

A flow-diverting stent is not a pressure-diverting stent

J J Schneiders1, E VanBavel, C B Majoie

  • 1Department of Radiology, Academic Medical Center, University of Amsterdam, Amsterdam, The Netherlands. j.j.schneiders@amc.uva.nl

AJNR. American Journal of Neuroradiology
|August 20, 2011
PubMed

More Related Videos

Novel and Innovative Hybrid Technique for Type A Aortic Dissection06:26

Novel and Innovative Hybrid Technique for Type A Aortic Dissection

Published on: March 28, 2025

Catheter-based Endovascular Angioplasty for Fibrosing Mediastinitis-associated Pulmonary Vein Stenosis06:59

Catheter-based Endovascular Angioplasty for Fibrosing Mediastinitis-associated Pulmonary Vein Stenosis

Published on: August 26, 2025

Related Concept Videos

Static, Stagnation, Dynamic and Total Pressure01:24

Static, Stagnation, Dynamic and Total Pressure

The concept of static, stagnation, dynamic, and total pressure is fundamental in fluid dynamics, often explained using Bernoulli's equation:
Bernoulli's Equation for Flow Normal to a Streamline01:16

Bernoulli's Equation for Flow Normal to a Streamline

Bernoulli's equation for flow normal to a streamline explains how pressure varies across curved streamlines due to the outward centrifugal forces induced by the fluid's curvature. The pressure is higher on the inner side of the curve, near the center of curvature, and decreases outward to balance these centrifugal forces.
The pressure difference depends on the fluid's velocity and radius of curvature. The pressure variation is minimal in flows with nearly straight streamlines. However, the...
Pipe Flowrate Measurement01:28

Pipe Flowrate Measurement

In pipe flow measurement, orifice, nozzle, and Venturi meters are commonly used to determine fluid flowrates by constricting the flow area, which increases fluid velocity and reduces pressure. This pressure difference, governed by Bernoulli's principle and adjusted for real-world conditions, is essential for calculating flowrate. Each meter type is suited to specific applications based on accuracy, efficiency, and compatibility with various flow conditions.
The orifice meter is a simple,...
Underflow Gates01:30

Underflow Gates

Underflow gates are vital for controlling water flow in irrigation canals. The three main types of underflow gates — vertical, radial, and drum gates — serve different purposes while ensuring effective flow management. Vertical gates move up and down, generating a free-flowing water jet; radial gates pivot to regulate the flow; and drum gates rotate for precise adjustments. The flow through these gates is influenced by downstream conditions, resulting in free or drowned outflow.Free and Drowned...
Introduction to Types of Flows01:23

Introduction to Types of Flows

Fluid flows are categorized by dimensionality and behavior, with one-dimensional flow being the simplest form, where properties like velocity and pressure change only along a single axis. Water moving through straight pipes exemplifies this flow type, as variations in other directions are minimal. One-dimensional analysis helps simplify understanding such flows, focusing solely on changes along the pipe's length.
Two-dimensional flow involves changes in both length and height, as seen in air...
Steady, Laminar Flow Between Parallel Plates01:17

Steady, Laminar Flow Between Parallel Plates

Understanding steady, laminar flow between parallel plates is essential for analyzing and designing flow in narrow rectangular channels, commonly found in various water conveyance and drainage systems. The Navier-Stokes equations govern fluid motion and are generally challenging to solve due to their nonlinearity. However, simplifications are possible in certain cases, like the steady laminar flow between parallel plates. For this scenario, we assume steady, incompressible, laminar flow.