Related Experiment Video

Updated: May 28, 2026

Synthetic, Multi-Layer, Self-Oscillating Vocal Fold Model Fabrication
10:16

Synthetic, Multi-Layer, Self-Oscillating Vocal Fold Model Fabrication

Published on: December 2, 2011

Modal parameters of two incomplete and complete guitars differing in the bracing pattern of the soundboard

Ewa Skrodzka1, Andrzej Łapa, Bogumił B J Linde

  • 1Faculty of String Instruments, Harp, Guitar and Luthiery, I. J. Paderewski Academy of Music, św. Marcin 87, 61-808 Poznań, Poland. afa@amu.edu.pl

The Journal of the Acoustical Society of America
|October 7, 2011
PubMed

More Related Videos

Dendrochronological Dating and Provenancing of String Instruments10:26

Dendrochronological Dating and Provenancing of String Instruments

Published on: October 6, 2022

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

Related Concept Videos

Problem-Solving: Tuning of a Guitar String01:04

Problem-Solving: Tuning of a Guitar String

In the case of stringed instruments like the guitar, the elastic property that determines the speed of the sound produced is its linear mass density or the mass per unit length. This is simply called the linear density. If the string's linear density is constant along the string, then the linear density is simply the total mass divided by the total length.
The string's wave speed can be regulated by varying the linear density. Tension is the other property that determines the speed of...
Modes of Standing Waves - I01:03

Modes of Standing Waves - I

A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. A building may vibrate for several seconds with a driving frequency matching the building's natural frequency of vibration; this produces a resonance that results in one building collapsing while the neighboring buildings do not. Often, buildings of a certain height are devastated, while other taller buildings remain intact. This phenomenon...
Modes of Standing Waves: II01:04

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end.
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
Sound Waves: Resonance01:14

Sound Waves: Resonance

Resonance is produced depending on the boundary conditions imposed on a wave. Resonance can be produced in a string under tension with symmetrical boundary conditions (i.e., has a node at each end). A node is defined as a fixed point where the string does not move. The symmetrical boundary conditions result in some frequencies resonating and producing standing waves, while other frequencies interfere destructively. Sound waves can resonate in a hollow tube, and the frequencies of the sound...
Cascaded Op Amps01:16

Cascaded Op Amps

Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...