Related Experiment Video

Updated: Aug 19, 2026

Optical Scatter Microscopy Based on Two-Dimensional Gabor Filters
14:58

Optical Scatter Microscopy Based on Two-Dimensional Gabor Filters

Published on: June 3, 2010

Detection of aberrant observations in a background of an unknown multidimensional Gaussian distribution

E S Gelsema1, B Leijnse, R W Wulkan

  • 1Department of Medical Informatics, Erasmus University, Rotterdam, The Netherlands.

Methods of Information in Medicine
|July 1, 1990
PubMed

More Related Videos

Identification of Disease-related Spatial Covariance Patterns using Neuroimaging Data14:27

Identification of Disease-related Spatial Covariance Patterns using Neuroimaging Data

Published on: June 26, 2013

Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns13:44

Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns

Published on: August 30, 2013

Related Concept Videos

What Are Outliers?01:12

What Are Outliers?

Outliers are observed data points that are far from the least squares line. They have unusual values and need to be examined carefully. Though an outlier may result from erroneous data, at other times, it may hold valuable information about the population under study and should be included in the data. Hence, it is crucial to examine what causes a data point to be an outlier.
The z score is used to find outliers or unusual values. It should be noted that any values beyond -2 and +2 are...
Outliers and Influential Points01:08

Outliers and Influential Points

An outlier is an observation of data that does not fit the rest of the data. It is sometimes called an extreme value. When you graph an outlier, it will appear not to fit the pattern of the graph. Some outliers are due to mistakes (for example, writing down 50 instead of 500), while others may indicate that something unusual is happening. Outliers are present far from the least squares line in the vertical direction. They have large "errors," where the "error" or residual is the vertical...
Random Error01:04

Random Error

Random or indeterminate errors originate from various uncontrollable variables, such as variations in environmental conditions, instrument imperfections, or the inherent variability of the phenomena being measured. Usually, these errors cannot be predicted, estimated, or characterized because their direction and magnitude often vary in magnitude and direction even during consecutive measurements. As a result, they are difficult to eliminate. However, the aggregate effect of these errors can be...
Detection of Gross Error: The Q Test01:00

Detection of Gross Error: The Q Test

When one or more data points appear far from the rest of the data, there is a need to determine whether they are outliers and whether they should be eliminated from the data set to ensure an accurate representation of the measured value. In many cases, outliers arise from gross errors (or human errors) and do not accurately reflect the underlying phenomenon. In some cases, however, these apparent outliers reflect true phenomenological differences. In these cases, we can use statistical methods...
Difference from Background: Limit of Detection01:05

Difference from Background: Limit of Detection

The limit of detection (LOD) is the smallest amount of analyte that can be distinguished from the background noise. The LOD value corresponds to the concentration at which the analyte signal is three times larger than the standard deviation of the blank signal. Below this value, the analyte signal cannot be differentiated from the background noise. It is calculated by dividing the calibration slope by 3 times the standard deviation of the blank signals.
The LOD indicates the presence or absence...
Quantifying and Rejecting Outliers: The Grubbs Test01:02

Quantifying and Rejecting Outliers: The Grubbs Test

Sometimes, a data set can have a recorded numerical observation that greatly  deviates from the rest of the data. Assuming that the data is normally distributed, a statistical method called the Grubbs test can be used to determine whether the observation is truly an outlier.  To perform a two-tailed Grubbs test, first, calculate the absolute difference between the outlier and the mean. Then, calculate the ratio between this difference and the standard deviation of the sample. This number is...