Related Experiment Video

Updated: May 25, 2026

Investigating the Potential of Singly Curved Thin Piezoelectric Transducers for Energy Harvesting and Structural Health Monitoring
07:02

Investigating the Potential of Singly Curved Thin Piezoelectric Transducers for Energy Harvesting and Structural Health Monitoring

Published on: November 14, 2025

Circular High-Q Resonating Isotropic Strain Sensors with Large Shift of Resonance Frequency under Stress

Rohat Melik1, Emre Unal, Nihan Kosku Perkgoz

  • 1Department of Electrical and Electronics Engineering, Bilkent University, Bilkent, 06800 Ankara, Turkey;

Sensors (Basel, Switzerland)
|February 4, 2012
PubMed

Keywords:
Q-factorRFICbioMEMS sensorscircular architecturefrequency shiftresonatorssensitivity

More Related Videos

Production of a Strain-Measuring Device with an Improved 3D Printer06:17

Production of a Strain-Measuring Device with an Improved 3D Printer

Published on: January 30, 2020

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

Related Concept Videos

Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Measurements of Strain01:27

Measurements of Strain

Strain quantifies the deformation of a material under force, typically measured as normal strain, which represents the change in length when compared with the original length. Electrical strain gauges are used for enhanced accuracy. These devices consist of a conductive wire mounted on a paper backing that adheres to the material's surface. These gauges operate on the piezoresistive effect, where the wire's electrical resistance changes in response to mechanical deformation. The strain gauge...
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the shaft's...
Elastic Strain Energy for Shearing Stresses01:20

Elastic Strain Energy for Shearing Stresses

As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...