Related Experiment Video

Updated: May 24, 2026

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal
06:24

High-Contrast and Fast Photorheological Switching of a Twist-Bend Nematic Liquid Crystal

Published on: October 31, 2019

Volume phase transitions of biaxial nematic elastomers

Akihiko Matsuyama1

  • 1Department of Bioscience and Bioinformatics, Faculty of Computer Science and Systems Engineering, Kyushu Institute of Technology, Kawazu 680-4, Iizuka, Fukuoka 820-8502, Japan. matuyama@bio.kyutech.ac.jp

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|March 10, 2012
PubMed

More Related Videos

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets06:26

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets

Published on: May 15, 2017

Microfluidic Preparation of Liquid Crystalline Elastomer Actuators12:04

Microfluidic Preparation of Liquid Crystalline Elastomer Actuators

Published on: May 20, 2018

Related Concept Videos

Phase Transitions02:31

Phase Transitions

Whether solid, liquid, or gas, a substance's state depends on the order and arrangement of its particles (atoms, molecules, or ions). Particles in the solid pack closely together, generally in a pattern. The particles vibrate about their fixed positions but do not move or squeeze past their neighbors. In liquids, although the particles are closely spaced, they are randomly arranged. The position of the particles are not fixed—that is, they are free to move past their neighbors to occupy...
Phase Transitions01:21

Phase Transitions

A phase transition is the process in which a substance changes from one state of matter to another, like from a solid to a liquid, liquid to gas, or vice versa, at a specific temperature and under given pressure conditions. This change is spontaneous and is affected by alterations in temperature and pressure. These parameters impact the strength of the forces between molecules (intermolecular forces) in the substance.During a phase transition, both the initial and final phases of the substance...
The Phase Rule01:20

The Phase Rule

The phase rule describes the relationship between the variance (degrees of freedom), the number of components, and the number of phases in a system at equilibrium.Variance is a concept that denotes the number of independent intensive properties (properties are those that do not depend on the amount of material in the system), such as temperature, pressure, and composition, that can be altered without impacting the number of phases in equilibrium.In a single-component system, such as pure water,...
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
Phase Diagrams of Ternary Systems01:28

Phase Diagrams of Ternary Systems

Consider a ternary system, which is composed of three components: water (W), ethanoic acid (E), and trichloromethane (T). Here, Ethanoic acid (E) is fully miscible with both water (W) and trichloromethane (T), meaning it can mix entirely with either of them. However, water and trichloromethane have partial miscibility, meaning they can only mix to a certain extent, beyond which two separate phases will form.The phase diagram of a ternary system is represented as an equilateral triangle, where...
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...