Related Experiment Video

Updated: May 24, 2026

Fabricating High-viscosity Droplets using Microfluidic Capillary Device with Phase-inversion Co-flow Structure
08:02

Fabricating High-viscosity Droplets using Microfluidic Capillary Device with Phase-inversion Co-flow Structure

Published on: April 17, 2018

Spreading profile of evaporative liquid drops in thin porous layer

W Y Chong1, K S Lim, W H Lim

  • 1Photonic Research Centre, Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur, Malaysia. wuyi80@yahoo.com

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|March 10, 2012
PubMed

More Related Videos

Glass-Based Devices to Generate Drops and Emulsions08:45

Glass-Based Devices to Generate Drops and Emulsions

Published on: April 5, 2022

Scalable Stamp Printing and Fabrication of Hemiwicking Surfaces06:16

Scalable Stamp Printing and Fabrication of Hemiwicking Surfaces

Published on: December 18, 2018

Related Concept Videos

Distillation: Vapor–Liquid Equilibria01:01

Distillation: Vapor–Liquid Equilibria

Distillation is a separation technique that takes advantage of the boiling point properties of disparate elements in a mixture. To perform distillation, we begin by heating a miscible mixture of two liquids with a significant difference in boiling points (at least 20°C). As the solution heats up and reaches the bubble point of the more volatile component, some molecules of the more volatile component transition into the gas phase and travel upward into the condenser, which is a glass tube with...
Capillarity in Fluid01:19

Capillarity in Fluid

Capillarity describes the movement of liquid in small spaces without external forces acting on it. The capillarity is driven by surface tension and adhesive interactions between the liquid and surrounding solid surfaces. This effect is often seen in narrow tubes, porous materials, and fine particles.
Surface tension is crucial to capillarity. It results from cohesive forces between liquid molecules at the liquid-air boundary, forming a skin that resists external forces. When the capillary tube...
Vaporization01:18

Vaporization

The physical form of a substance changes by changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. For vaporization to occur, kinetic energy must be greater than the intermolecular forces that keep molecules bonded. The amount of energy needed to vaporize a quantity of liquid at a given pressure and a constant temperature is called the heat of vaporization. When...
Surface Tension01:24

Surface Tension

Surface tension is defined as the force per unit length (γ) acting along the surface of a liquid. It arises due to strong intermolecular forces of attraction. A molecule located inside the bulk of the liquid is surrounded by other molecules and experiences equal forces in all directions. However, a molecule at the surface experiences unbalanced forces because there are more neighboring molecules below than above. This creates a net inward force that pulls surface molecules toward the interior,...
Theories of Dissolution: Diffusion Layer Model01:15

Theories of Dissolution: Diffusion Layer Model

Dissolution, the process by which drug particles dissolve in a solvent, is explained by the diffusion layer model, a theoretical framework that simulates the absorption of oral drugs and allows us to analyze experimental data.
This process starts with a thin layer, saturated with the drug, forming at the interface between the solid and liquid. The solute then diffuses from this layer into the main solution. The Noyes-Whitney equation suggests that the rate of dissolution relies on the diffusion...
Rise of Liquid in a Capillary Tube01:18

Rise of Liquid in a Capillary Tube

When very thin cylindrical tubes, called capillaries, are dipped in a liquid, the liquid rises or falls in the tube compared to the surrounding liquid. This phenomenon is called capillary action. Capillary action occurs due to the combination of two opposing forces: the cohesive forces of the liquid, which cause it to stick to itself and form a rounded shape, and the adhesive forces between the liquid and the walls of the container, which cause the liquid to be attracted to the container walls.