Related Experiment Video

Updated: May 24, 2026

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes
06:56

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

Published on: May 23, 2017

Direct measurement of bend-induced mode deformation in large-mode-area fibers

R C G Smith1, A M Sarangan, Z Jiang

  • 1Institute of Optics, University of Rochester, Rochester, New York 14627, USA. rismith@optics.rochester.edu

Optics Express
|March 16, 2012
PubMed

More Related Videos

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

Measuring the Mechanical Properties of Living Cells Using Atomic Force Microscopy08:41

Measuring the Mechanical Properties of Living Cells Using Atomic Force Microscopy

Published on: June 27, 2013

Related Concept Videos

Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member is the...
Deformation of a Beam under Transverse Loading01:15

Deformation of a Beam under Transverse Loading

Understanding beam deflection, particularly for indeterminate beams with overhanging segments and multiple concentrated loads, is crucial for ensuring structural integrity and functionality. The process begins with constructing an accurate free-body diagram, which helps identify the forces and moments acting on the beam. This diagram is vital for visualizing how bending moments vary along the beam's length, influencing its curvature.
The insights from the bending moment diagram extend to...
Flexural Stress01:16

Flexural Stress

When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
Beams with Symmetric Loadings01:15

Beams with Symmetric Loadings

The moment-area method is an analytical tool used in structural engineering to determine the slope and deflection of beams under various loads. Consider a cantilever with a concentrated load and moment at the free end. The first step is constructing a free-body diagram to calculate the reactions at the fixed end. Next, the bending moment diagram is plotted to visualize how the bending moment varies along the beam's length, focusing on points where the bending moment equals zero.
The M/EI...