Related Experiment Video

Updated: May 23, 2026

Development of a Novel Internal Fixation Model for Rat Radial Fractures: Fracture Healing Assessment and Dorsal Root Ganglion Isolation
11:21

Development of a Novel Internal Fixation Model for Rat Radial Fractures: Fracture Healing Assessment and Dorsal Root Ganglion Isolation

Published on: March 13, 2026

Three-dimensional deformity analysis of malunited distal radius fractures and their influence on wrist and forearm

J Miyake1, T Murase, Y Yamanaka

  • 1Department of Orthopaedic Surgery, Osaka University Graduate School of Medicine, Osaka, Japan. miyake-osk@umin.ac.jp

The Journal of Hand Surgery, European Volume
|April 13, 2012
PubMed

More Related Videos

Novel Triple-Loop Technique for Suturing TFCC Injuries without Transosseous Tunnel08:27

Novel Triple-Loop Technique for Suturing TFCC Injuries without Transosseous Tunnel

Published on: May 23, 2025

Related Concept Videos

Bones of the Upper Limb: Ulna01:15

Bones of the Upper Limb: Ulna

The ulna and radius are parallel bones of the antebrachium or the forearm. The ulna lies medially and consists of a bony tip called the olecranon process at its proximal end. This hook-like projection articulates with the olecranon fossa of the humerus and forms the "hinged" ulnohumeral part of the elbow joint. This joint facilitates forearm extension and flexion while preventing its hyperextension. Similarly, the coronoid process, another bony projection on the proximal/anterior side of the...
Bones of the Upper Limb: Radius01:09

Bones of the Upper Limb: Radius

The radius is longer of the two bones that make up the human antebrachium or forearm. At the proximal end, the radius articulates with the capitulum of the humerus and the radial notch of the ulna to form the elbow joint. At the distal end, the radius articulates with the ulna via the ulnar notch, forming the distal radioulnar joint. Distally, the radius also attaches to the carpal wrist bones (scaphoid and lunate) to form the radiocarpal joint.
The radius has a nail-shaped head, and a short...
Bones of the Upper Limb: Humerus01:19

Bones of the Upper Limb: Humerus

The upper limb consists of the arm, forearm, wrist, and hand bones. The humerus is the single bone of the upper arm region. Proximally, it has a large, spherical, smooth head that articulates with the glenoid cavity of the scapula to form the glenohumeral or shoulder joint. The margin of the head is the anatomical neck, a residual epiphyseal plate. Laterally it extends to form bony projections called the greater tubercle and the lesser tubercle. Next to the tubercles is the surgical neck, a...
Functional Classification of Joints01:09

Functional Classification of Joints

Functional Classification of Joints
The functional classification of joints is determined by the amount of mobility between the adjacent bones. Joints are functionally classified as a synarthrosis or immobile joint, an amphiarthrosis or slightly moveable joint, or as a diarthrosis, a freely moveable joint. Fibrous and cartilaginous joints can be functionally classified as either synarthroses  or amphiarthroses, whereas all synovial joints are classified as diarthroses.
Synarthrosis
An immobile...
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...