Related Experiment Video
Updated: May 22, 2026
Pretreatment of Lignocellulosic Biomass with Low-cost Ionic Liquids
Published on: August 10, 2016
Dialkylimidazolium ionic liquids hydrolyze cellulose under mild conditions
1Department of Chemical and Biomolecular Engineering, University of California, Berkeley, CA 94720-1462, USA.
Abstract:
The average molecular weight of cellulose derived from filter paper, poplar, and Avicel decreases by up to two orders of magnitude during typical mild dissolution protocols using ionic liquids (ILs). About an order of magnitude greater cellulose depolymerization rate during ionic liquid dissolution occurs in 1-butyl-3-methylimidazolium chloride (BmimCl) and 1-ethyl-3-methylimidazolium chloride (EmimCl) compared to 1-ethyl-3-methylimidazolium acetate (EmimOAc), and, unintuitively, greater IL purity results in greater cellulose depolymerization. The following data support the mechanism of cellulose hydrolysis to be acid-catalyzed: (i) increase in number of reducing ends following cellulose dissolution in IL; (ii) addition of N-methylimidazolium base suppresses cellulose depolymerization during dissolution in IL; (iii) small amounts of glucose and traces of hydroxymethyl furfural are present following cellulose dissolution in IL. The acid is presumably synthesized via IL decomposition to generate a carbene and proton, consistent with hypothesis derived from molecular modeling. Titration experiments conducted here measure the amount of acid synthesized to be in the 4000 ppm range for high-purity BmimCl IL during mild processing conditions for cellulose dissolution. This data is relevant for understanding the extent of IL decomposition during biomass dissolution.
More Related Videos
08:09A Novel Method for the Pentosan Analysis Present in Jute Biomass and Its Conversion into Sugar Monomers Using Acidic Ionic Liquid
Published on: June 1, 2018
06:31Highly Stereoselective Synthesis of 1,6-Ketoesters Mediated by Ionic Liquids: A Three-component Reaction Enabling Rapid Access to a New Class of Low Molecular Weight Gelators
Published on: November 27, 2015
Related Concept Videos
01:19Acid Halides to Alcohols: LiAlH4 Reduction
The mechanism proceeds in three steps. First, the nucleophilic hydride ion attacks the carbonyl carbon of the acid halide to form a tetrahedral intermediate. Next, the carbonyl group is re-formed, and the halide ion departs as a leaving group, generating an aldehyde. A second nucleophilic attack by the hydride yields an alkoxide ion, which, upon protonation, gives a primary alcohol as...
01:01Acid Halides to Carboxylic Acids: Hydrolysis
As shown below, the mechanism involves a nucleophilic attack by water at the carbonyl carbon to form a tetrahedral intermediate. This is followed by the reformation of the carbon–oxygen π bond along with the departure of a halide ion. A final proton transfer step yields carboxylic acid...
01:20Aldehydes and Ketones with Water: Hydrate Formation
The formation of hydrates is a reversible reaction. Hydrate formation is influenced by steric and electronic factors accompanying the alkyl substituents on the carbonyl group: The rate of hydrate formation increases with a decrease in the number of alkyl groups attached to the carbonyl carbon. Hence,...
01:12Acid Halides to Esters: Alcoholysis
01:15Cellulose and Pectic Polysaccharides
As a cell matures, its cell wall specializes according to its type. For example, the parenchyma cells of...
01:20Amides to Amines: LiAlH4 Reduction
Amide reduction requires two equivalents of the reducing agent, acting as a source of hydride ions. As shown in the figure, the reaction is initiated with a nucleophilic attack by the hydride ion at the carbonyl carbon to form a tetrahedral intermediate.