Related Experiment Video

Updated: May 19, 2026

Minimum Burning Pressures of Water-based Emulsion Explosives
08:35

Minimum Burning Pressures of Water-based Emulsion Explosives

Published on: October 31, 2017

A real explosion: the requirement of steam explosion pretreatment

Zhengdao Yu1, Bailiang Zhang, Fuqiang Yu

  • 1College of Mechanical and Electrical Engineering, Henan Agricultural University, Zhengzhou 450002, China.

Bioresource Technology
|August 4, 2012
PubMed

More Related Videos

Biomass Conversion to Produce Hydrocarbon Liquid Fuel Via Hot-vapor Filtered Fast Pyrolysis and Catalytic Hydrotreating11:28

Biomass Conversion to Produce Hydrocarbon Liquid Fuel Via Hot-vapor Filtered Fast Pyrolysis and Catalytic Hydrotreating

Published on: December 25, 2016

Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor07:30

Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor

Published on: September 9, 2016

Related Concept Videos

Methods of Sterilization I: Physical Methods01:29

Methods of Sterilization I: Physical Methods

As used in a healthcare facility, sterilization destroys all microorganisms through physical or chemical methods. The physical method includes steam, dry heat, boiling water, and radiation.
Steam sterilization uses non-toxic, low-cost moist heat in the form of saturated steam under pressure, which is fast, microbicidal, and sporicidal, and quickly warms and penetrates fabrics. Autoclaves, or steam sterilizers, expose each item to direct steam contact for a predetermined time at the necessary...
The Joule and Joule–Thomson Experiments01:23

The Joule and Joule–Thomson Experiments

Consider an adiabatic system composed of two chambers, A and B, designed such that no heat flows into or out of the system. Initially, chamber A is filled with a gas at a fixed temperature T1, pressure p1, and volume V1, while chamber B is evacuated. The gas is then gradually forced through a rigid, porous barrier to chamber B, ultimately reaching temperature T2, pressure p2, and volume V2. A piston on the right side maintains a constant pressure (p2), which is lower than p1. The significant...
Accelerated Curing of Concrete01:25

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
Atomic Absorption Spectroscopy: Atomization Methods01:25

Atomic Absorption Spectroscopy: Atomization Methods

Atomic Absorption Spectroscopy (AAS) atomizes samples through flame atomization or electrothermal atomization. Flame atomization typically involves a nebulizer and spray chamber assembly to combine the sample with a fuel–oxidant mixture, creating a fine aerosol mist that enters a burner. Typically, the fuel and oxidant are combined in an approximately stoichiometric ratio. However, for atoms that are easily oxidized, a fuel-rich mixture may be more advantageous. Only about 5% of the aerosol...
Methods of Sterilization II: Chemical Methods01:30

Methods of Sterilization II: Chemical Methods

In healthcare, the chemical method of sterilization uses chemical sterilants to treat surgical instruments and medical supplies to help prevent the transmission of infectious pathogens to patients. Due to heat sensitivity, most medical supplies and equipment should not be exposed to high temperatures. These parts include rubber, plastic, glass, and other similar elements.
Using chemical sterilization rather than heat to clean out equipment is recommended. It eradicates and removes all bacteria,...
Washing, Drying, and Ignition of Precipitates00:52

Washing, Drying, and Ignition of Precipitates

After filtration, the precipitate is washed to remove coprecipitated impurities and any remaining mother liquor. Colloidal precipitates, such as silver chloride, are washed with an electrolyte (such as dilute nitric acid) to prevent the peptization of the precipitate. In the case of slightly soluble precipitates, the wash solution contains a common ion to reduce solubility. Lead sulfate, which is slightly soluble in water, is washed with dilute sulfuric acid. Similarly, wash solutions may be...