Related Experiment Video

Updated: Feb 11, 2026

Urethroplasty with Pedicled Tunica Vaginalis for the Treatment of Long-segment Anterior Urethral Stricture Caused by Lichen Sclerosus of Glans Penis
03:55

Urethroplasty with Pedicled Tunica Vaginalis for the Treatment of Long-segment Anterior Urethral Stricture Caused by Lichen Sclerosus of Glans Penis

Published on: October 18, 2024

937

Urethral mesh erosion after single-incision mid-urethral sling

Steven Minaglia1, Ian A Oyama

  • 1Division of Urogynecology and Pelvic Reconstructive Surgery, Department of Obstetrics and Gynecology, John A. Burns School of Medicine, University of Hawaii, Honolulu, Hawaii, HI 96826, USA. minaglia@hawaii.edu

Female Pelvic Medicine & Reconstructive Surgery
|September 18, 2012
PubMed
Abstract

More Related Videos

Urethral Stricture Induction Followed by Buccal Mucosa Graft Urethroplasty in a Rat Model05:09

Urethral Stricture Induction Followed by Buccal Mucosa Graft Urethroplasty in a Rat Model

Published on: April 28, 2023

1.6K
Nerve-sparing Mid-urethral Obstruction NeMO in Female Small Rodents07:42

Nerve-sparing Mid-urethral Obstruction NeMO in Female Small Rodents

Published on: April 25, 2017

10.0K

Related Concept Videos

Mesh Analysis01:20

Mesh Analysis

Mesh analysis is a valuable method for simplifying circuit analysis using mesh currents as key circuit variables. Unlike nodal analysis, which focuses on determining unknown voltages, mesh analysis applies Kirchhoff's voltage law (KVL) to find unknown currents within a circuit. This method is particularly convenient in reducing the number of simultaneous equations that need to be solved.
A fundamental concept in mesh analysis is the definition of meshes and mesh currents. A mesh is a closed...
1.5K
Mesh Analysis with Current Sources01:10

Mesh Analysis with Current Sources

Mesh analysis becomes simpler when analyzing circuits with current sources, whether independent or dependent. The presence of current sources reduces the number of equations required for analysis. Two cases illustrate this:
Current Source in One Mesh: The analysis process is straightforward when a current source is found in only one mesh within the circuit. Mesh currents are assigned as usual, with the mesh containing the current source excluded from the analysis. Kirchhoff's voltage law...
2.0K
Mesh Analysis for AC Circuits01:12

Mesh Analysis for AC Circuits

In the domain of radio communication, the significance of impedance matching must be considered. It is crucial to ensure the efficient transmission of signals between radio transmitters and receivers. Achieving this balance involves using impedance-matching circuits, with one fundamental configuration comprising a resistor, capacitor, and inductor.
The process of harmonizing these impedances begins with a clear understanding of the input and output signals. Once these signals are known, the...
714
Load along a Single Axis01:29

Load along a Single Axis

In structural engineering, the analysis of beams subjected to varying loads is a critical aspect of understanding the behavior and performance of these structural elements. A common scenario involves a beam subjected to a combination of different load distributions.
Consider a beam of length L subjected to a varying load, which is a combination of parabolic and trapezoidal load distribution along the x-axis. In this case, it is essential to determine the resultant loads, their locations, and...
648
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
462
Angular Momentum: Single Particle01:10

Angular Momentum: Single Particle

Angular momentum is directed perpendicular to the plane of the rotation, and its magnitude depends on the choice of the origin. The perpendicular vector joining the linear momentum vector of an object to the origin is called the “lever arm.” If the lever arm and linear momentum are collinear, then the magnitude of the angular momentum is zero. Therefore, in this case, the object rotates about the origin such that it lies on the rim of the circumference defined by the lever arm...
7.8K