Related Experiment Video

Updated: May 18, 2026

Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses
11:19

Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses

Published on: October 21, 2016

Assessment of internal condition of waste in a roofed landfill

Xin Zhang1, Toshihiko Matsuto

  • 1Lab of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13, Nishi 8, Kita-ku, Sapporo 060-8628, Japan.

Waste Management (New York, N.Y.)
|September 20, 2012
PubMed

More Related Videos

Biocontained Carcass Composting for Control of Infectious Disease Outbreak in Livestock14:34

Biocontained Carcass Composting for Control of Infectious Disease Outbreak in Livestock

Published on: May 6, 2010

Design and Construction of an Experimental Setup to Enhance Mineral Weathering through the Activity of Soil Organisms07:22

Design and Construction of an Experimental Setup to Enhance Mineral Weathering through the Activity of Soil Organisms

Published on: November 10, 2023

Related Concept Videos

Cavity Drainage and Flashings in Masonry walls01:20

Cavity Drainage and Flashings in Masonry walls

Typically, a cavity wall consists of two wythes separated by a gap of at least 2 inches, which may contain insulation while still maintaining a minimum clear space of 1 inch to facilitate adequate drainage. Advanced methods like the insertion of a continuous drainage mat can further reduce this space while ensuring effective moisture expulsion.
Weep holes, strategically placed at the base of the cavity, are critical for draining accumulated water. These openings are created by leaving head...
Assessment of the Rectum and Anus01:25

Assessment of the Rectum and Anus

Evaluating the rectum and anus plays a crucial role in conducting a thorough physical examination of the gastrointestinal system. Although it may be uncomfortable and often embarrassing for the patient, it holds immense diagnostic value, particularly in detecting gastrointestinal diseases and abnormalities. This guide will explain how to perform this assessment using inspection and palpation methods.
Rectal Inspection
Begin by inspecting the perianal and anal areas for color, texture, rashes,...
Design Example: Maintaining Level of an Embankment01:19

Design Example: Maintaining Level of an Embankment

Constructing a roadway embankment over uneven terrain requires precise leveling to ensure stability and proper drainage. Surveyors use a leveling instrument and staff to calculate ground elevations and determine the required fill material at each point along the embankment alignment.The process begins by positioning a leveling instrument near a benchmark with a known elevation. A backsight reading establishes the instrument height, which serves as a reference for subsequent measurements. A...
Slump Test01:20

Slump Test

The slump test is a widely used method to measure the workability of concrete. It employs a 12-inch high truncated cone mold that tapers from eight inches at the base to four inches at the top. Before testing, the mold is securely attached to a flat base and dampened.
Concrete is poured into the mold in three layers to conduct the test. Each layer is compacted 25 times with a steel tamping rod, which has a five-eighths-inch diameter and a rounded end, to ensure even distribution and eliminate...
Design Example: Managing Concrete Workability01:14

Design Example: Managing Concrete Workability

This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.
To address...
Unsoundness of Aggregate due to Volume Change01:26

Unsoundness of Aggregate due to Volume Change

Unsoundness in aggregates due to volume changes is primarily caused by the physical alterations aggregates undergo, such as freezing and thawing, thermal changes, and wetting and drying. Unsound aggregates, when subjected to these changes, result in volume change upon disintegration. This, in turn, contributes to the deterioration of concrete, including scaling, pop-outs, and cracking. Particular types of aggregates, such as porous flints, cherts, and those containing clay minerals, are...