Related Experiment Video

Updated: May 18, 2026

Aqueous Droplets Used as Enzymatic Microreactors and Their Electromagnetic Actuation
08:27

Aqueous Droplets Used as Enzymatic Microreactors and Their Electromagnetic Actuation

Published on: August 28, 2017

Evaporation of picoliter droplets on surfaces with a range of wettabilities and thermal conductivities

E L Talbot1, A Berson, P S Brown

  • 1Department of Chemistry, Durham University, Durham, DH1 3LE, United Kingdom.

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|September 26, 2012
PubMed

More Related Videos

Taking Advantage of Reduced Droplet-surface Interaction to Optimize Transport of Bioanalytes in Digital Microfluidics07:57

Taking Advantage of Reduced Droplet-surface Interaction to Optimize Transport of Bioanalytes in Digital Microfluidics

Published on: November 10, 2014

A Microfluidic Chip for ICPMS Sample Introduction11:16

A Microfluidic Chip for ICPMS Sample Introduction

Published on: March 5, 2015

Related Concept Videos

Vaporization01:18

Vaporization

The physical form of a substance changes by changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. For vaporization to occur, kinetic energy must be greater than the intermolecular forces that keep molecules bonded. The amount of energy needed to vaporize a quantity of liquid at a given pressure and a constant temperature is called the heat of vaporization. When...
Surface Tension01:24

Surface Tension

Surface tension is defined as the force per unit length (γ) acting along the surface of a liquid. It arises due to strong intermolecular forces of attraction. A molecule located inside the bulk of the liquid is surrounded by other molecules and experiences equal forces in all directions. However, a molecule at the surface experiences unbalanced forces because there are more neighboring molecules below than above. This creates a net inward force that pulls surface molecules toward the interior,...
Phase Transitions: Vaporization and Condensation02:39

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. Vaporization occurs when the thermal motion of the molecules overcome the intermolecular forces, and the molecules (at the surface) escape into the gaseous state. When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules...
Distillation: Vapor–Liquid Equilibria01:01

Distillation: Vapor–Liquid Equilibria

Distillation is a separation technique that takes advantage of the boiling point properties of disparate elements in a mixture. To perform distillation, we begin by heating a miscible mixture of two liquids with a significant difference in boiling points (at least 20°C). As the solution heats up and reaches the bubble point of the more volatile component, some molecules of the more volatile component transition into the gas phase and travel upward into the condenser, which is a glass tube with...
Preparation of Samples for Electron Microscopy01:20

Preparation of Samples for Electron Microscopy

To be visualized by an electron microscope, either transmission or scanning, biological samples need to be fixed (stabilized) so the electron beam does not destroy them and dried thoroughly (desiccated/dehydrated) so the vacuum does not affect them. Fixation needs to be done as quickly as possible because the sample properties will start changing as soon as it is removed from its natural environment. For example, in a tissue sample, the oxygen levels begin decreasing, causing an altered...
Sublimation01:03

Sublimation

Sublimation is the direct transformation of a solid to a gaseous state. For instance, at standard pressure and room temperature, solid carbon dioxide sublimes to gaseous carbon dioxide. The phase diagram depicts the conditions required for sublimation. This process occurs at the solid-gas phase boundary and is not observed above the triple point of the substance. The reverse of sublimation is called deposition, where a gaseous substance condenses directly into a solid. Sublimation and...