Related Experiment Video

Updated: May 17, 2026

In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx
09:49

In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx

Published on: May 13, 2020

Variation of anode grid surface morphology and its effect on operation of a triode virtual cathode oscillator

Qifu Xu1, Dan Cai, Qiang Zhang

  • 1College of Optoelectronic Science and Engineering, National University of Defense Technology, Changsha 410073, China.

The Review of Scientific Instruments
|November 7, 2012
PubMed

More Related Videos

The Effect of Anodization Parameters on the Aluminum Oxide Dielectric Layer of Thin-Film Transistors12:32

The Effect of Anodization Parameters on the Aluminum Oxide Dielectric Layer of Thin-Film Transistors

Published on: May 24, 2020

Ambient Method for the Production of an Ionically Gated Carbon Nanotube Common Cathode in Tandem Organic Solar Cells14:37

Ambient Method for the Production of an Ionically Gated Carbon Nanotube Common Cathode in Tandem Organic Solar Cells

Published on: November 5, 2014

Related Concept Videos

Van de Graaff Generator01:15

Van de Graaff Generator

Van de Graaff generators (or Van de Graaffs) are devices used to demonstrate high voltage due to static electricity that can also be used for research. Robert Van de Graaff first built one in 1931 (based on original suggestions by Lord Kelvin) for use in nuclear physics research.
Van de Graaff uses both smooth and pointed surfaces, conductors, and insulators to generate large static charges and, hence, large voltages. A substantial excess charge can be deposited on the sphere because it moves...
Characteristics of Practical Op Amps01:16

Characteristics of Practical Op Amps

A difference amplifier, a crucial component in numerous electronic devices, ideally amplifies only the difference-mode signal, which is the difference between two input signals. However, in practical circuits, the output voltage depends on both the differential gain and the common-mode gain.
The ratio of differential gain to the common-mode gain is defined as the common-mode rejection ratio (CMRR). This ratio quantifies the ability of operational amplifiers (op-amps) to reject common-mode...
Modeling of Diode Reverse Characteristics01:14

Modeling of Diode Reverse Characteristics

In electronic circuits, reverse-biased diode configurations are critical for regulating voltage levels. Zener diodes exploit the reverse breakdown phenomenon and exhibit a controlled breakdown at a specific Zener voltage (VZ). They are designed to maintain a constant voltage across their terminals and are commonly used for voltage regulation in circuits.
When a reverse voltage applied to a Zener diode exceeds its breakdown voltage, the diode enters the breakdown region. At this point, the...
Modeling of Diode Forward Characteristics01:19

Modeling of Diode Forward Characteristics

Understanding the behavior of diodes when forward-biased is a fundamental aspect of electronic circuit design and analysis. This analysis primarily utilizes two models: the exponential diode model and the constant-voltage-drop model. The exponential model comes into play when the source voltage exceeds 0.5 volts, pushing the diode current to rise exponentially above the saturation current. This relationship is graphically depicted in the current-voltage (I-V) curve, illustrating the diode's...
Cascaded Op Amps01:16

Cascaded Op Amps

Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
Oscillations In An LC Circuit01:30

Oscillations In An LC Circuit

An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by