Related Experiment Video

Updated: May 14, 2026

Combustion Characterization and Model Fuel Development for Micro-tubular Flame-assisted Fuel Cells
08:16

Combustion Characterization and Model Fuel Development for Micro-tubular Flame-assisted Fuel Cells

Published on: October 2, 2016

Application of multicriteria decision making methods to compression ignition engine efficiency and gaseous,

Nicholas C Surawski1, Branka Miljevic, Timothy A Bodisco

  • 1International Laboratory for Air Quality and Health, Queensland University of Technology, 2 George Street, Brisbane QLD 4001, Australia.

Environmental Science & Technology
|January 25, 2013
PubMed

More Related Videos

Implementation of Portable Emissions Measurement Systems (PEMS) for the Real-driving Emissions (RDE) Regulation in Europe09:34

Implementation of Portable Emissions Measurement Systems (PEMS) for the Real-driving Emissions (RDE) Regulation in Europe

Published on: December 4, 2016

A Rapid Method for Modeling a Variable Cycle Engine04:58

A Rapid Method for Modeling a Variable Cycle Engine

Published on: August 13, 2019

Related Concept Videos

Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
Turnover Number and Catalytic Efficiency01:19

Turnover Number and Catalytic Efficiency

The turnover number of an enzyme is the maximum number of substrate molecules it can transform per unit time. Turnover numbers for most enzymes range from 1 to 1000 molecules per second. Catalase has the known highest turnover number, capable of converting up to 2.8×106 molecules of hydrogen peroxide into water and oxygen per second. Lysozyme has the lowest known turnover number of half a molecule per second.
Chymotrypsin is a pancreatic enzyme that breaks down proteins during digestion. The...
Methods of Medium Optimization01:28

Methods of Medium Optimization

Optimizing growth media enhances microbial proliferation and maximizes product yield. Statistical experimental design methodologies provide structured and reproducible approaches, offering progressively higher levels of robustness and efficiency.The One-Factor-at-a-Time (OFAT) MethodThe One-Factor-at-a-Time (OFAT) method involves adjusting a single variable while keeping all others constant. However, it cannot detect interactions between variables, often leading to suboptimal outcomes when...
Heat Engines01:10

Heat Engines

A heat engine is a device used to extract heat from a source and then convert it into mechanical work used for various applications. For example, a steam engine on an old-style train can produce the work needed for driving the train.
Whenever we consider heat engines (and associated devices such as refrigerators and heat pumps), we do not use the standard sign convention for heat and work. For convenience, we assume that the symbols Qh, Qc, and W represent only the amounts of heat transferred...