Related Experiment Video

Updated: May 13, 2026

Deposition of Porous Sorbents on Fabric Supports
05:58

Deposition of Porous Sorbents on Fabric Supports

Published on: June 12, 2018

Effect of impregnating agent and relative humidity on surface characteristics of sorbents determined by inverse gas

M Kasperkowiak1, J Kołodziejek, B Strzemiecka

  • 1Poznan University of Technology, Institute of Chemical Technology and Engineering, pl. M. Skłodowskiej-Curie 2, 60-965 Poznań, Poland. malgorzata.kasperkowiak@yahoo.pl

Journal of Chromatography. A
|March 26, 2013
PubMed

More Related Videos

A Synthetic Methodology for Preparing Impregnated and Grafted Amine-Based Silica Composites for Carbon Capture08:00

A Synthetic Methodology for Preparing Impregnated and Grafted Amine-Based Silica Composites for Carbon Capture

Published on: September 29, 2023

In situ FTIR Spectroscopy as a Tool for Investigation of Gas/Solid Interaction: Water-Enhanced CO2 Adsorption in UiO-66 Metal-Organic Framework11:38

In situ FTIR Spectroscopy as a Tool for Investigation of Gas/Solid Interaction: Water-Enhanced CO2 Adsorption in UiO-66 Metal-Organic Framework

Published on: February 1, 2020

Related Concept Videos

Adsorption of Gases on Solids01:28

Adsorption of Gases on Solids

Adsorption is a process where molecules, known as the adsorbates, accumulate on a surface, which is referred to as the adsorbent or substrate. Occurring at the solid-gas interface, this phenomenon is crucial in various scientific and industrial contexts. The reverse of adsorption is desorption.Two types of adsorptions exist: physical (physisorption) and chemical (chemisorption). Physisorption involves gas molecules held to the solid's surface by relatively weak intermolecular van der Waals...
Adsorption Isotherms I01:29

Adsorption Isotherms I

Adsorption isotherms are mathematical models that describe how molecules in a gas or liquid phase interact with surfaces. Two of the most common isotherm models are the Langmuir and Freundlich isotherms, which relate to Type I monolayer chemisorption. The Langmuir model is based on four key assumptions:• Adsorption cannot exceed monolayer coverage.• All surface sites are equivalent.• Molecules adsorb only at vacant sites.• There are no interactions between adsorbed molecules.Consider the...
Gas Chromatography: Introduction01:13

Gas Chromatography: Introduction

Gas chromatography (GC) is a technique for separating and analyzing volatile compounds in a sample. Its primary purpose is to identify and quantify components in complex mixtures, making it essential in fields such as environmental analysis, pharmaceuticals, and petrochemicals. GC is also called vapor-phase chromatography (VPC) or gas-liquid partition chromatography (GLPC).
In GC,  a sample is vaporized and mixed with an inert carrier gas (the mobile phase), which transports it through a column.
Volatilization01:10

Volatilization

Volatilization gravimetry is an analytical technique that measures the mass lost due to the volatilization of the substance. This technique is used to estimate the amount of volatile material in a sample. To perform this method, heat a known amount of the sample to a high temperature in a crucible or other suitable vessel. The volatile substance in the sample evaporates, and the vapor is completely expelled from the crucible either by heating the sample or bubbling a stream of inert gas through...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...
Adsorption Isotherms II01:25

Adsorption Isotherms II

Brunauer, Emmett, and Teller (BET) introduced a theory in 1938 that modified Langmuir's assumptions to explain multilayer physical adsorption. This theory is applicable to Type II isotherms and provides a more realistic picture of adsorption processes. The BET theory assumes a uniform solid surface with localized adsorption sites, where adsorption at one site doesn't affect adsorption at neighboring sites. This theory also allows for the possibility of additional molecules being adsorbed on top...