Analysis of tractor-related deaths

Related Experiment Video

Updated: May 12, 2026

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor
09:35

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor

Published on: June 16, 2021

Zerrin Erkol1, Bora Buken, Yavuz Hekimoglu

  • 1Department of Forensic Medicine, Abant Izzet Baysal University Medical Faculty, Bolu, Turkey. zerrinerkol@gmail.com

Journal of Agromedicine
|April 2, 2013
PubMed

More Related Videos

A Test Bed to Examine Helmet Fit and Retention and Biomechanical Measures of Head and Neck Injury in Simulated Impact07:30

A Test Bed to Examine Helmet Fit and Retention and Biomechanical Measures of Head and Neck Injury in Simulated Impact

Published on: September 21, 2017

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research07:15

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research

Published on: December 18, 2020

Related Concept Videos

Survey Safety01:28

Survey Safety

Surveying near highways, rough terrain, or power lines involves significant risks. Working along highways is particularly dangerous and requires the use of warning signs and flagmen. It is safest to avoid working directly on roads and use offsets whenever possible. When highway work is unavoidable, it must follow all safety guidelines. Surveyors should wear bright clothing, such as orange reflective vests, to ensure visibility to motorists, coworkers, and hunters. In construction zones, wearing...
Truncation in Survival Analysis01:09

Truncation in Survival Analysis

Truncation in survival analysis refers to the exclusion of individuals or events from the dataset based on specific criteria related to the time of the event. This exclusion can happen in two primary forms: left truncation and right truncation.
Left truncation occurs when individuals who experienced the event of interest before a certain time are not included in the study. This is often due to a "delayed entry" into the study where only those who survive until a certain entry point are observed.
Hypothesis Test for Test of Independence01:16

Hypothesis Test for Test of Independence

The test of independence is a chi-square-based test used to determine whether two variables or factors are independent or dependent. This hypothesis test is used to examine the independence of the variables. One can construct two qualitative survey questions or experiments based on the variables in a contingency table. The goal is to see if the two variables are unrelated (independent) or related (dependent). The null and alternative hypotheses for this test are:
H0: The two variables (factors)...
Relative Motion Analysis using Rotating Axes-Problem Solving01:29

Relative Motion Analysis using Rotating Axes-Problem Solving

Consider a crane whose telescopic boom rotates with an angular velocity of 0.04 rad/s and angular acceleration of 0.02 rad/s2. Along with the rotation, the boom also extends linearly with a uniform speed of 5 m/s. The extension of the boom is measured at point D, which is measured with respect to the fixed point C on the other end of the boom. For the given instant, the distance between points C and D is 60 meters.
Here, in order to determine the magnitude of velocity and acceleration for point...
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...