Related Experiment Video

Updated: May 12, 2026

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone (ITZ)
08:59

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone (ITZ)

Published on: December 16, 2019

Smooth ROC curves and surfaces for markers subject to a limit of detection using monotone natural cubic splines

Leonidas E Bantis1, John V Tsimikas, Stelios D Georgiou

  • 1Department of Statistics and Actuarial-Financial Mathematics, University of the Aegean, Samos 83200, Greece.

Biometrical Journal. Biometrische Zeitschrift
|April 5, 2013
PubMed

Keywords:
CensoringConstrained least squaresDiagnostic accuracySmooth distribution functionSmooth survival estimation

More Related Videos

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces08:05

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces

Published on: September 9, 2022

Multimodal Cross-Device and Marker-Free Co-Registration of Preclinical Imaging Modalities07:13

Multimodal Cross-Device and Marker-Free Co-Registration of Preclinical Imaging Modalities

Published on: October 27, 2023

Related Concept Videos

Curve Sketching and Derivatives01:22

Curve Sketching and Derivatives

Understanding the behavior of a function through its first and second derivatives is essential for analyzing its graph. Derivatives provide insight into where a function increases or decreases, where it attains local maxima or minima, and how its curvature behaves across different intervals.The first derivative of a function reveals the slope of the tangent line at any given point. Points where the derivative is zero or undefined are considered critical, as they often indicate potential extrema...
Limits with Oscillating Discontinuities01:19

Limits with Oscillating Discontinuities

An oscillating discontinuity is a type of discontinuity in which a function’s values fluctuate infinitely often as the input approaches a particular point. Unlike jump discontinuities, where the function suddenly shifts between two values, or infinite discontinuities, where the function diverges without bound, an oscillating discontinuity arises from rapid back-and-forth variation. Because the function never stabilizes toward a single value, no finite limit exists at that point.One of the most...
Elevation of Intermediate Points on Vertical Curves01:20

Elevation of Intermediate Points on Vertical Curves

Vertical curves are essential in roadway design because they provide smooth transitions between varying roadway grades. Designing vertical curves involves calculating intermediate elevations and identifying the curve's highest or lowest point, which is essential for optimal roadway performance.Intermediate elevations on a vertical curve are determined using the tangent offset method. This method considers the initial elevation at the start of the curve, the grades, and the curve's geometry. The...
Introduction to Horizontal Curves01:19

Introduction to Horizontal Curves

Horizontal curves are essential in highway and railroad design, ensuring smooth and safe transitions between straight path segments, or tangents. These curves allow vehicles to maintain speed without abrupt changes, minimizing accidents and improving travel efficiency.A horizontal curve is typically defined by its geometric relationship to two tangents that meet at an intersection point (P.I.), where a simple curve is introduced to connect them. The back tangent refers to the initial tangent...
Guidelines for Sketching a Curve01:23

Guidelines for Sketching a Curve

Curve sketching is a systematic method for understanding the overall behavior of a function by analyzing its key mathematical features. A function defines a curve on the coordinate plane, where the horizontal axis represents the input variable and the vertical axis represents the output. The process begins by determining the domain, which specifies the set of input values for which the function is defined and establishes the horizontal extent of the graph.Intercepts with the horizontal and...
Bending of Curved Members - Neutral Surface01:16

Bending of Curved Members - Neutral Surface

In curved beams, unlike straight beams, the stress distribution across the cross-section is not uniform due to the beam's curvature. This non-uniformity arises because the neutral axis, where stress is zero, does not align with the centroid of the section. In a curved beam, the strain varies along the section as a function of the distance from the neutral axis.
Consider the curved member described in the previous lesson. According to Hooke's law, which relates stress to strain within the...