Related Experiment Video

Updated: May 10, 2026

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials
11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

Stress distribution around osseointegrated implants with different internal-cone connections: photoelastic and finite

Lilian Costa Anami1, Júlia Magalhães da Costa Lima, Fernando Eidi Takahashi

  • 11  Graduate Program in Restorative Dentistry, Prosthetic Dentistry Unit, Institute of Science and Technology - São José dos Campos, Univ Estadual Paulista (UNESP), Brazil.

The Journal of Oral Implantology
|June 12, 2013
PubMed

Keywords:
finite element analysisinternal-cone connectionsphotoelasticity

More Related Videos

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint07:09

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

Published on: March 7, 2014

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees14:31

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees

Published on: July 15, 2009

Related Concept Videos

Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
General State of Stress01:21

General State of Stress

The general state of stress within a material can be accurately depicted using a stress tensor. This tensor encapsulates the internal forces distributed within a material subjected to external forces or deformations.
Specifically, consider a tetrahedral element where one face, labeled XYZ, is perpendicular to the line OA, and the remaining faces align with the coordinate axes with point O as the origin. At any point, such as point O, the stress tensor can be used to determine the stress...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Components of Stress01:23

Components of Stress

Stress analysis under multiple loading conditions is intricate, necessitating a comprehensive grasp of normal and shearing stresses. Consider a small cube at point O, subjected to stress on all six faces, visible or not. Normal stress components σx, σy, σz act perpendicularly to the x, y, and z axes. Shearing stress components τxy and τxz are exerted on faces perpendicular to these axes.
Interestingly, the hidden cube faces also experience these stresses, equal and opposite to those on the...