Related Experiment Video

Updated: May 10, 2026

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates
07:53

Cutting Procedures, Tensile Testing, and Ageing of Flexible Unidirectional Composite Laminates

Published on: April 27, 2019

[Analysis of stresses developing in the evidence-bearing material affected by a bladed article]

S V Leonov, Iu P Butuzova

    Sudebno-Meditsinskaia Ekspertiza
    |June 27, 2013
    PubMed

    More Related Videos

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

    Published on: August 7, 2018

    A Method for Studying the Temperature Dependence of Dynamic Fracture and Fragmentation09:12

    A Method for Studying the Temperature Dependence of Dynamic Fracture and Fragmentation

    Published on: June 28, 2015

    Related Concept Videos

    Applications of Stress01:04

    Applications of Stress

    Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
    The...
    Stress: General Loading Conditions01:15

    Stress: General Loading Conditions

    To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
    The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
    Bearing Stress01:22

    Bearing Stress

    Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
    Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
    Stresses under Combined Loadings01:23

    Stresses under Combined Loadings

    When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
    The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
    Stress Concentrations01:24

    Stress Concentrations

    Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
    Stress Concentrations01:13

    Stress Concentrations

    The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
    The stress concentration...