Related Experiment Video

Updated: May 7, 2026

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy
07:44

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

Published on: April 27, 2016

Phase diagram and piezoelectric response of (Ba₁-xCax)(Zr₀.₁Ti₀.₉)O₃ solid solution

Desheng Fu1, Yuto Kamai, Naonori Sakamoto

  • 1Department of Electronics and Materials Science, Graduate School of Engineering, Shizuoka University, 3-5-1 Johoku, Naka-ku, Hamamatsu 432-8561, Japan.

Journal of Physics. Condensed Matter : an Institute of Physics Journal
|October 3, 2013
PubMed

More Related Videos

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties11:07

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties

Published on: August 15, 2015

Chemical Synthesis of Porous Barium Titanate Thin Film and Thermal Stabilization of Ferroelectric Phase by Porosity-Induced Strain08:00

Chemical Synthesis of Porous Barium Titanate Thin Film and Thermal Stabilization of Ferroelectric Phase by Porosity-Induced Strain

Published on: March 27, 2018

Related Concept Videos

Solid–Solid Solutions01:24

Solid–Solid Solutions

The temperature-composition phase diagram of two solids, A and B, which are immiscible in the solid phase but form miscible liquids, shows that when the temperature is low, these two exist as separate, pure solids (A and B). As the temperature increases, they transition into a single-phase liquid solution where A and B coexist. Moving from point a1 to a2 in the phase diagram, the composition changes such that solid B begins to separate from the solution, enriching the remaining liquid with A.
Phase Diagram01:24

Phase Diagram

A phase diagram is a graphical representation of the physical states of a substance under different conditions of temperature and pressure. It shows the boundaries between solid, liquid, and gas phases and the conditions at which these phases coexist in equilibrium. An area in a phase diagram represents a single phase, whereas lines or phase boundaries represent the equilibrium between two phases.In the phase diagram of water, the boundary line between the solid and liquid states illustrates...
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
Phase Diagrams of Ternary Systems01:28

Phase Diagrams of Ternary Systems

Consider a ternary system, which is composed of three components: water (W), ethanoic acid (E), and trichloromethane (T). Here, Ethanoic acid (E) is fully miscible with both water (W) and trichloromethane (T), meaning it can mix entirely with either of them. However, water and trichloromethane have partial miscibility, meaning they can only mix to a certain extent, beyond which two separate phases will form.The phase diagram of a ternary system is represented as an equilateral triangle, where...