Related Experiment Video

Updated: May 7, 2026

Measurement of Chladni Mode Shapes with an Optical Lever Method
04:39

Measurement of Chladni Mode Shapes with an Optical Lever Method

Published on: June 5, 2020

5.1K

Modal density and modal distribution of bending wave vibration fields in ribbed plates

Kristoffer Ahrens Dickow1, Jonas Brunskog, Mogens Ohlrich

  • 1Department of Civil Engineering, Aalborg University, Aalborg DK-9000, Denmark.

The Journal of the Acoustical Society of America
|October 15, 2013
PubMed

More Related Videos

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

Published on: May 23, 2017

11.1K
Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

2.8K

Related Concept Videos

Flexural Stress01:16

Flexural Stress

When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
910
Design of Prismatic Beams for Bending01:23

Design of Prismatic Beams for Bending

The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and...
680
Distribution of Stresses in a Narrow Rectangular Beam01:11

Distribution of Stresses in a Narrow Rectangular Beam

In studying beam stress distribution, examining an elemental section is essential. To determine the average shearing stress on this face, the calculated shear is divided by the surface area. Importantly, shearing stresses on the beam's transverse and horizontal planes mirror each other, indicating a consistent stress distribution along the upper region of the beam. Notably, shearing stresses are absent at the beam's upper and lower surfaces due to the absence of applied forces in these...
728
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
538
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
766
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
827