Analyzing axial stress and deformation of tubular for steam injection process in deviated wells based on the varied

Related Experiment Video

Updated: May 6, 2026

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores
09:32

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores

Published on: November 20, 2014

11.8K

Yunqiang Liu1, Jiuping Xu, Shize Wang

  • 1Uncertainty Decision-Making Laboratory, Sichuan University, Chengdu 610064, China ; College of Economics & Management, Sichuan Agricultural University, Chengdu 611130, China.

Thescientificworldjournal
|October 29, 2013
PubMed

More Related Videos

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

2.8K
Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole09:37

Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole

Published on: August 26, 2019

5.3K

Related Concept Videos

Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
607
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
740
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
745
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
743
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
687
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
744