Related Experiment Video

Updated: May 6, 2026

Stereo-Imaging System DLT Calibration to Capture 3D In Situ Displacements of Stretched Peripheral Nerves
06:26

Stereo-Imaging System DLT Calibration to Capture 3D In Situ Displacements of Stretched Peripheral Nerves

Published on: January 12, 2024

890

Linear representation of temporal location and Stevens's law

B S Gorman1, A E Wessman, G R Schmeidler

  • 1The City College of the City University of New York, 10031, New York, New York.

Memory & Cognition
|November 12, 2013
PubMed

More Related Videos

Temporal Ordering of Dynamic Expression Data from Detailed Spatial Expression Maps11:52

Temporal Ordering of Dynamic Expression Data from Detailed Spatial Expression Maps

Published on: February 9, 2017

7.5K
Measurement & Analysis of the Temporal Discrimination Threshold Applied to Cervical Dystonia10:05

Measurement & Analysis of the Temporal Discrimination Threshold Applied to Cervical Dystonia

Published on: January 27, 2018

8.7K

Related Concept Videos

State Space Representation01:27

State Space Representation

The frequency-domain technique, commonly used in analyzing and designing feedback control systems, is effective for linear, time-invariant systems. However, it falls short when dealing with nonlinear, time-varying, and multiple-input multiple-output systems. The time-domain or state-space approach addresses these limitations by utilizing state variables to construct simultaneous, first-order differential equations, known as state equations, for an nth-order system.
Consider an RLC circuit, a...
786
Linear time-invariant Systems01:23

Linear time-invariant Systems

A system is linear if it displays the characteristics of homogeneity and additivity, together termed the superposition property. This principle is fundamental in all linear systems. Linear time-invariant (LTI) systems include systems with linear elements and constant parameters.
The input-output behavior of an LTI system can be fully defined by its response to an impulsive excitation at its input. Once this impulse response is known, the system's reaction to any other input can be...
1.1K
Basic Discrete Time Signals01:16

Basic Discrete Time Signals

The unit step sequence is defined as 1 for zero and positive values of the integer n. This sequence can be graphically displayed using a set of eight sample points, showing a step function starting from n=0 and remaining constant thereafter.
The unit impulse or sample sequence is mathematically expressed as zero for all n values except at n=0, where it is one. The unit impulse sequence, denoted by δ(n), is the first difference of the unit step sequence, while the unit step sequence u(n) is...
971
Linear Approximation in Time Domain01:21

Linear Approximation in Time Domain

Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
460
Trapezoidal Rule01:26

Trapezoidal Rule

Estimating the distance traveled by a vehicle using its recorded velocity over time is a common problem in physics and engineering. When velocity data is available at discrete time intervals, rather than as a continuous function, numerical integration methods such as the trapezoidal rule are often employed to approximate the total displacement.The trapezoidal rule works by dividing the total time interval into several equal segments. Within each segment, the recorded velocities at the endpoints...
283
Evaluating Limits by Direct Substitution01:29

Evaluating Limits by Direct Substitution

In the analysis of functions that represent continuous physical phenomena, it is often necessary to determine the output value as the input approaches a specific point. When a combination of algebraic terms defines the function and exhibits no discontinuities or abrupt changes near the point of interest, the limit of the function can be evaluated directly. This process, known as direct substitution, involves replacing the variable in the expression with the value it approaches.Direct...
274