Related Experiment Video

Updated: May 4, 2026

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System
10:52

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Published on: August 7, 2018

7.9K

Influence of different post-core systems on impact stress: a pilot study

Yoshihiro Kondoh1, Tomotaka Takeda2, Takamitsu Ozawa2

  • 1Department of General Dentistry, Tokyo Dental College Chiba Hospital.

The Open Dentistry Journal
|December 21, 2013
PubMed
Abstract

Keywords:
Accelerationdistortionglass fiber-reinforced epoxy resin postimpact forcepost-core systemroot.

More Related Videos

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

11.8K
In Vitro Impact Model to Generate Sublethal Chondrocyte Injury in Bovine Cartilage Explants06:42

In Vitro Impact Model to Generate Sublethal Chondrocyte Injury in Bovine Cartilage Explants

Published on: June 27, 2025

659

Related Concept Videos

Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
604
Bearing Stress01:22

Bearing Stress

Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
2.6K
Impact Strength of Concrete01:21

Impact Strength of Concrete

Impact strength in concrete is a critical measure that reflects the material's capability to endure the forces applied during pile driving and when supporting machinery foundations that experience impulsive loads. It is also essential when handling precast concrete components to prevent accidental damage. The impact strength is assessed by observing the concrete's resistance to repeated impacts and energy absorption capacity. A key indicator of significant damage to concrete is when it...
747
Residual Stresses01:26

Residual Stresses

Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...
1.1K
Normal Stress01:19

Normal Stress

Normal stress is a type of stress that occurs when forces act perpendicular, or normal, to a material's cross-sectional area. This stress often arises in structures when subjected to axial loading, which is the application of force along the axis of an object. A practical example of this can be found in bridge truss members.
When a rod is under axial loading, the internal forces and corresponding stress are normal to the plane of the section, so it is termed normal stress. It's important to...
1.5K
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
739