Related Experiment Video

Updated: May 3, 2026

Experimental Methods to Study Human Postural Control
08:12

Experimental Methods to Study Human Postural Control

Published on: September 11, 2019

9.1K

Center of pressure velocity reflects body acceleration rather than body velocity during quiet standing

Kei Masani1, Albert H Vette2, Masaki O Abe3

  • 1Rehabilitation Engineering Laboratory, Lyndhurst Centre, Toronto Rehabilitation Institute-University Health Network, 520 Sutherland Drive, Toronto, Ontario M4G 3V9, Canada; Rehabilitation Engineering Laboratory, Institute of Biomaterials and Biomedical Engineering, University of Toronto, 164 College Street, Toronto, Ontario M5S 3G9, Canada.

Gait & Posture
|January 22, 2014
PubMed

Keywords:
Center of pressureHuman posturePosturographyStanding

More Related Videos

Postural Organization of Gait Initiation for Biomechanical Analysis Using Force Platform Recordings06:21

Postural Organization of Gait Initiation for Biomechanical Analysis Using Force Platform Recordings

Published on: July 26, 2022

2.4K
Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

8.1K

Related Concept Videos

Static Equilibrium - I01:05

Static Equilibrium - I

A rigid body is said to be in dynamic equilibrium when both its linear and angular acceleration are zero, relative to an inertial frame of reference. This means that a body in equilibrium can be moving, but only when its linear and angular velocities are constant. A rigid body is said to be in static equilibrium when it is at rest in the selected frame of reference. The distinction between static equilibrium (e.g., a state of rest) and dynamic equilibrium (e.g, a state of uniform motion) is...
13.4K
Velocity and Acceleration in Steady and Unsteady Flow01:11

Velocity and Acceleration in Steady and Unsteady Flow

In fluid mechanics, velocity and acceleration are key concepts for analyzing particle motion in both steady and unsteady flow. Consider a fluid particle moving along a pathline, where its velocity depends on its position and time. The particle's acceleration is obtained by differentiating the velocity with respect to time.
The acceleration can be generalized to any point in the flow, and expressed as components along three perpendicular directions, representing changes in velocity over...
523
Velocity and Position by Graphical Method01:34

Velocity and Position by Graphical Method

Velocity and position can be calculated from the known function of acceleration as a function of time. The total area under the acceleration-time graph and the velocity-time graph gives the change in velocity and position, respectively. In the case of an airplane, its acceleration is tracked using the inertial navigation system. The pilot provides the input of the airplane's initial position and velocity before takeoff. The inertial navigation system then uses the acceleration data to...
9.3K
Instantaneous Acceleration01:16

Instantaneous Acceleration

Acceleration is in the direction of the change in velocity, but it is not always in the direction of motion. When an object slows down, its acceleration is opposite to the direction of its motion. Although commonly referred to as deceleration, this causes confusion in our analysis as deceleration is not a vector, and does not point to a specific direction with respect to a coordinate system. Therefore, the term deceleration is not used. For example, when a subway train slows down, it...
20.3K
Instantaneous Center of Zero Velocity01:20

Instantaneous Center of Zero Velocity

General plane motion, often observed in a rolling wheel, refers to a type of movement where the wheel is simultaneously rotating and translating. This complex motion can be understood by breaking it down into individual components.
To analyze this, consider two points on the wheel: point A and point B. The absolute velocity of point B can be expressed as the vector sum of the absolute velocity of point A and the relative velocity of point B with respect to point A. To simplify this analysis,...
1.0K
Uniform Circular Motion01:14

Uniform Circular Motion

Uniform circular motion is a specific type of motion in which an object travels in a circle with a constant speed. For example, any point on a propeller spinning at a constant rate is undergoing uniform circular motion. The second, minute, and hour hands of a watch also undergo uniform circular motion. It is hard to believe that points on these rotating objects are actually accelerating, even though the rotation rate is constant. To understand this, we must analyze the motion in terms of...
18.8K