Related Experiment Video

Updated: May 3, 2026

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation
09:39

In-situ Tapering of Chalcogenide Fiber for Mid-infrared Supercontinuum Generation

Published on: May 27, 2013

11.7K

Intra super-channel fiber nonlinearity compensation in flex-grid optical networks

Danish Rafique, Talha Rahman, Antonio Napoli

    Optics Express
    |February 12, 2014
    PubMed

    More Related Videos

    Writing Bragg Gratings in Multicore Fibers08:48

    Writing Bragg Gratings in Multicore Fibers

    Published on: April 20, 2016

    8.2K
    Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light09:19

    Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light

    Published on: July 29, 2013

    10.9K

    Related Concept Videos

    Load-frequency control01:28

    Load-frequency control

    Load-frequency control (LFC) is vital for maintaining power system stability, ensuring that frequency and power flows remain within acceptable limits during load changes. Turbine-governor control eliminates rotor accelerations and decelerations following load changes. However, a steady-state frequency error persists when the change in the turbine-governor reference setting is zero. In an interconnected power system, each area agrees to export or import a scheduled amount of power through...
    894
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    815
    Fiber Reinforced Concrete01:22

    Fiber Reinforced Concrete

    Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...
    639
    Reducing Line Loss01:18

    Reducing Line Loss

    In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
    With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss...
    524
    Flexural Stress01:16

    Flexural Stress

    When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
    Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
    906
    Elastic Curve from the Load Distribution01:16

    Elastic Curve from the Load Distribution

    The structural behavior of beams under distributed loads is critical for engineering analysis, which focuses on predicting how beams bend and react under such conditions. Different types of beams (e.g., cantilever, supported, or overhanging) behave differently under distributed load conditions.
    For all beams, the analysis of the beam's reaction to distributed loads begins by understanding the relationship between a beam's load and the resulting shear forces and bending moments. Initially, this...
    588