Related Experiment Video

Updated: May 1, 2026

Separation of Uranium and Thorium for 230Th-U Dating of Submarine Hydrothermal Sulfides
08:43

Separation of Uranium and Thorium for 230Th-U Dating of Submarine Hydrothermal Sulfides

Published on: May 20, 2019

6.2K

Thoron and thoron progeny measurements in German clay houses

S Gierl1, O Meisenberg2, P Feistenauer1

  • 1Helmholtz Zentrum München, German Research Center for Environmental Health, Institute of Radiation Protection, Ingolstädter Landstr. 1, 85764 Neuherberg, Germany.

Radiation Protection Dosimetry
|April 19, 2014
PubMed

More Related Videos

Preparing an Isotopically Pure 229Th Ion Beam for Studies of 229mTh10:42

Preparing an Isotopically Pure 229Th Ion Beam for Studies of 229mTh

Published on: May 3, 2019

8.5K
Phase-Dependent Control of Trap Depth and Persistent Luminescence in Strontium Aluminate Phosphors06:16

Phase-Dependent Control of Trap Depth and Persistent Luminescence in Strontium Aluminate Phosphors

Published on: December 5, 2025

381

Related Concept Videos

Thermal Insulation in Masonry Walls01:22

Thermal Insulation in Masonry Walls

In hot, dry climates, the thermal mass of masonry walls can be beneficial, absorbing heat during the day and releasing it at night, thereby stabilizing indoor temperatures. However, in most other climates, additional insulation is necessary to enhance thermal resistance.
External insulation can be applied using an Exterior Insulation and Finish System (EIFS), which involves affixing panels of plastic foam to the wall and covering them with a polymeric stucco reinforced with glass fiber mesh....
768
Measurement of Air Content in Concrete01:23

Measurement of Air Content in Concrete

Air content measurement in concrete is critical for ensuring structural integrity and durability of concrete structures, especially in environments prone to severe weather conditions. Accurate air content analysis optimizes concrete's resistance to freeze-thaw cycles and enhances its workability and strength. Several methods are standardized under ASTM guidelines to measure the air content in fresh concrete, each suitable for different concrete types and conditions.
The pressure method,...
938
Brick Masonry01:12

Brick Masonry

Brick masonry uses bricks as the building blocks and involves building walls from individual bricks laid in mortar. The basic building block of brick masonry is the wythe, a vertical layer of bricks with a thickness of one brick. Within a wythe, bricks can be laid in various courses or patterns, with the most common being the stretcher course, where bricks are laid with their long edge horizontal and face parallel to the wall.
For thicker walls, multiple wythes are bonded together using...
832
Composite Masonry Walls01:18

Composite Masonry Walls

Composite masonry walls combine multiple wythes of the same or different masonry materials to create a unified structure. These walls feature wythes that are bonded together either through mortar-filled collar joints, grouted spaces, or more commonly, with rigid metal ties and reinforcements, with the use of masonry header units being rare. Metal ties are preferred because they effectively minimize water penetration, as these walls primarily absorb moisture and then release it into the...
2.3K
Pressure Relationships in Thoracic Cavity01:24

Pressure Relationships in Thoracic Cavity

Breathing, otherwise known as pulmonary ventilation, is the process of air movement into and out of the lungs. The main mechanisms propelling pulmonary ventilation are atmospheric pressure (Patm), intra-pulmonary (Ppul ) or intra-alveolar pressure (Palv) within the alveoli, and intrapleural pressure (Pip) within the pleural cavity.
Breathing Mechanisms
Both intra-alveolar and intrapleural pressures rely on specific lung properties. The ability to breathe—allowing air to enter the lungs...
8.4K
Mortar Joints in Brick Masonry01:25

Mortar Joints in Brick Masonry

Mortar joints play a critical role in brick masonry, filling the spaces between brick to bind them together and provide structural integrity and strength. The thickness of these joints is variable, typically ranging from less than one-fourth inch to over half an inch, based on structural needs and specific applications.
The process of joint tooling is implemented as the mortar begins to harden. This technique involves compacting and shaping the mortar to enhance both the appearance and the...
657