Related Experiment Video

Updated: Apr 30, 2026

Closed-loop Neuro-robotic Experiments to Test Computational Properties of Neuronal Networks
11:18

Closed-loop Neuro-robotic Experiments to Test Computational Properties of Neuronal Networks

Published on: March 2, 2015

11.5K

Robust exponential stability of uncertain delayed neural networks with stochastic perturbation and impulse effects

Tingwen Huang, Chuandong Li, Shukai Duan

    IEEE Transactions on Neural Networks and Learning Systems
    |May 9, 2014
    PubMed

    More Related Videos

    Time-dependent Increase in the Network Response to the Stimulation of Neuronal Cell Cultures on Micro-electrode Arrays10:45

    Time-dependent Increase in the Network Response to the Stimulation of Neuronal Cell Cultures on Micro-electrode Arrays

    Published on: May 29, 2017

    10.8K
    Stochastic Noise Application for the Assessment of Medial Vestibular Nucleus Neuron Sensitivity In Vitro06:22

    Stochastic Noise Application for the Assessment of Medial Vestibular Nucleus Neuron Sensitivity In Vitro

    Published on: August 28, 2019

    4.7K

    Related Concept Videos

    Propagation of Uncertainty from Random Error00:59

    Propagation of Uncertainty from Random Error

    An experiment often consists of more than a single step. In this case, measurements at each step give rise to uncertainty. Because the measurements occur in successive steps, the uncertainty in one step necessarily contributes to that in the subsequent step. As we perform statistical analysis on these types of experiments, we must learn to account for the propagation of uncertainty from one step to the next. The propagation of uncertainty depends on the type of arithmetic operation performed on...
    1.9K
    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this...
    1.4K
    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    1.1K
    Transient and Steady-state Response01:24

    Transient and Steady-state Response

    In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
    These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
    756
    Time-Domain Interpretation of PD Control01:07

    Time-Domain Interpretation of PD Control

    Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
    Consider the example of control of motor torque. Initially, a positive...
    500
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    557